MC908AP64ACFAE Freescale Semiconductor, MC908AP64ACFAE Datasheet - Page 89

• Manufacturer Part Number: MC908AP64ACFAE
• Description: IC MCU 64K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64ACFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Core: HC08
• Processor Series: HC08AP
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 8 MHz
• Data Ram Size: 2 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Mounting Style: SMD/SMT
• Height: 1.4 mm
• Interface Type: SCI, SPI
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 7 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

6.5.1 PLL Control Register
The PLL control register (PCTL) contains the interrupt enable and flag bits, the on/off switch, the base
clock selector bit, the prescaler bits, and the VCO power-of-two range selector bits.
PLLIE — PLL Interrupt Enable Bit
PLLF — PLL Interrupt Flag Bit
PLLON — PLL On Bit
BCS — Base Clock Select Bit
Freescale Semiconductor
This read/write bit enables the PLL to generate an interrupt request when the LOCK bit toggles, setting
the PLL flag, PLLF. When the AUTO bit in the PLL bandwidth control register (PBWC) is clear, PLLIE
cannot be written and reads as logic 0. Reset clears the PLLIE bit.
This read-only bit is set whenever the LOCK bit toggles. PLLF generates an interrupt request if the
PLLIE bit also is set. PLLF always reads as logic 0 when the AUTO bit in the PLL bandwidth control
register (PBWC) is clear. Clear the PLLF bit by reading the PLL control register. Reset clears the PLLF
bit.
This read/write bit activates the PLL and enables the VCO clock, CGMVCLK. PLLON cannot be
cleared if the VCO clock is driving the base clock, CGMOUT (BCS = 1). (See
Selector
This read/write bit selects either the oscillator output, CGMXCLK, or the divided VCO clock,
CGMPCLK, as the source of the CGM output, CGMOUT. CGMOUT frequency is one-half the
frequency of the selected clock. BCS cannot be set while the PLLON bit is clear. After toggling BCS,
it may take up to three CGMXCLK and three CGMPCLK cycles to complete the transition from one
source clock to the other. During the transition, CGMOUT is held in stasis. (See
Selector
1 = PLL interrupts enabled
0 = PLL interrupts disabled
1 = Change in lock condition
0 = No change in lock condition
1 = PLL on
0 = PLL off
1 = CGMPCLK divided by two drives CGMOUT
0 = CGMXCLK divided by two drives CGMOUT
Circuit.) Reset sets this bit so that the loop can stabilize as the MCU is powering up.
Circuit.) Reset clears the BCS bit.
Address:
Do not inadvertently clear the PLLF bit. Any read or read-modify-write
operation on the PLL control register clears the PLLF bit.
Reset:
Read:
Write:
$0036
PLLIE
Bit 7
0
Figure 6-4. PLL Control Register (PCTL)
= Unimplemented
PLLF
MC68HC908AP A-Family Data Sheet, Rev. 3
6
0
PLLON
5
1
NOTE
BCS
4
0
PRE1
3
0
PRE0
2
0
VPR1
1
0
6.3.8 Base Clock
6.3.8 Base Clock
VPR0
Bit 0
0
CGM Registers
89