TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 177

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

Table 15-8 Flash Memory Writing Mode Process
BOOT
ROM
15.6.2 Flash Memory Writing Mode (Operation command: 30H)
Note 1: “xxH × 3” indicates that the device enters the halt condition after sending 3 bytes of xxH. For details, refer to " 15.7 Error
Note 2: Refer to " 15.9 Intel Hex Format (Binary) ".
Note 3: Refer to " 15.8 Checksum (SUM) ".
Note 4: Refer to " 15.10 Passwords ".
Note 5: If addresses from FFE0H to FFFFH are filled with “FFH”, the passwords are not compared because the device is consid-
Note 6: If the read protection is enabled or a password error occurs, TMP86FH46ANG stops UART communication and enters the
Note 7: If an error occurs during the reception of a password address or a password string, TMP86FH46ANG stops UART com-
1st byte
2nd byte
3rd byte
4th byte
5th byte
6th byte
7th byte
8th byte
9th byte
10th byte
11th byte
12th byte
13th byte
14th byte
15th byte
m’th byte
m’th + 1 byte
n’th - 2 byte
n’th - 1 byte
n’th byte
n’th + 1 byte
:
:
Table 15-8 shows flash memory writing mode process.
Transfer Byte
Code ".
ered as a blank product. Transmitting a password string is not required. Even in the case of a blank product , it is required
to specify the password count storage address and the password comparison start address. Transmit these data from the
external controller. If a password error occurs due to incorrect password count storage address or password comparison
start address, TMP86FH46ANG stops UART communication and enters the halt condition. Therefore, when a password
error occurs, initialize TMP86FH46ANG by the
halt confition. In this case, initialize TMP86FH46ANG by the
munication and enters the halt condition. In this case, initialize TMP86FH46ANG by the
serial PROM mode.
Matching data (5Ah)
-
Baud rate modification data
(See Table 15-4)
-
Operation command data (30H)
-
Password count storage address bit
15 to 08 (Note 4)
Password count storage address bit
07 to 00 (Note 4)
Password comparison start address
bit 15 to 08 (Note 4)
Password comparison start address
bit 07 to 00 (Note 4)
Password string (Note 5)
-
Intel Hex format (binary)
(Note 2)
-
-
(Wait state for the next operation com-
mand data)
Transfer Data from External Controller
to TMP86FH46ANG
Page 163
RESET
9600 bps
9600 bps
9600 bps
9600 bps
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
pin and reactivate the serial ROM mode.
RESET
Baud Rate
pin and reactivate the serial ROM mode.
- (Automatic baud rate adjustment)
OK: Echo back data (5AH)
Error: Nothing transmitted
-
OK: Echo back data
Error: A1H × 3, A3H × 3, 62H × 3 (Note 1)
-
OK: Echo back data (30H)
Error: A1H × 3, A3H × 3, 63H × 3 (Note 1)
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted)
-
OK: Nothing transmitted
Error: Nothing transmitted
-
-
OK: SUM (Upper byte) (Note 3)
Error: Nothing transmitted
OK: SUM (Lower byte) (Note 3)
Error: Nothing transmitted
-
Transfer Data from TMP86FH46ANG to
RESET
External Controller
pin and reactivate the
TMP86FH46ANG