C8051F338-GMR Silicon Laboratories Inc, C8051F338-GMR Datasheet - Page 101

• Manufacturer Part Number: C8051F338-GMR
• Description: IC MCU 16K FLASH 24QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F33xr

Specifications of C8051F338-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-QFN
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F336DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• On-chip Dac: 10 bit
• Height: 0.73 mm
• Length: 4 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: Q4962654; T1084322

17.1. Power-On Reset
During power-up, the device is held in a reset state and the RST pin is driven low until V
V
increases (V
power-on and V
cause the device to be released from reset before V
1 ms, the power-on reset delay (T
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is
set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other
resets). Since all resets cause program execution to begin at the same location (0x0000) software can
read the PORSF flag to determine if a power-up was the cause of reset. The content of internal data mem-
ory should be assumed to be undefined after a power-on reset. The V
power-on reset.
RST
. A delay occurs before the device is released from reset; the delay decreases as the V
DD
Logic HIGH
DD
Logic LOW
ramp time is defined as how fast V
Figure 17.2. Power-On and V
2.70
2.55
2.0
1.0
monitor reset timing. The maximum V
/RST
V
RST
PORDelay
Power-On
Reset
) is typically less than 0.3 ms.
T
PORDelay
Rev.1.0
DD
DD
DD
reaches the V
ramps from 0 V to V
DD
Monitor Reset Timing
ramp time is 1 ms; slower ramp times may
Monitor
Reset
VDD
RST
C8051F336/7/8/9
DD
level. For ramp times less than
monitor is enabled following a
RST
). Figure 17.2. plots the
VDD
DD
t
settles above
DD
ramp time
101