C8051F332-GMR Silicon Laboratories Inc, C8051F332-GMR Datasheet - Page 64

• Manufacturer Part Number: C8051F332-GMR
• Description: IC 8051 MCU 4K FLASH 20MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F33xr

Specifications of C8051F332-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-QFN
• For Use With: 336-1451 - ADAPTER PROGRAM TOOLSTICK F330
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

logic 1 upon a Comparator falling-edge occurrence, and the CP0RIF flag is set to logic 1 upon the Com-
parator rising-edge occurrence. Once set, these bits remain set until cleared by software. The Comparator
rising-edge interrupt mask is enabled by setting CP0RIE to a logic 1. The Comparator0 falling-edge inter-
rupt mask is enabled by setting CP0FIE to a logic 1.
The output state of the Comparator can be obtained at any time by reading the CP0OUT bit. The Compar-
ator is enabled by setting the CP0EN bit to logic 1, and is disabled by clearing this bit to logic 0.
Note that false rising edges and falling edges can be detected when the comparator is first powered on or
if changes are made to the hysteresis or response time control bits. Therefore, it is recommended that the
rising-edge and falling-edge flags be explicitly cleared to logic 0 a short time after the comparator is
enabled or its mode bits have been changed. This Power Up Time is specified in Table 8.1 on page 70.
Bit7:
Bit6:
Bit5:
Bit4:
Bits3–2: CP0HYP1–0: Comparator0 Positive Hysteresis Control Bits.
Bits1–0: CP0HYN1–0: Comparator0 Negative Hysteresis Control Bits.
CP0EN
R/W
Bit7
CP0EN: Comparator0 Enable Bit.
0: Comparator0 Disabled.
1: Comparator0 Enabled.
CP0OUT: Comparator0 Output State Flag.
0: Voltage on CP0+ < CP0–.
1: Voltage on CP0+ > CP0–.
CP0RIF: Comparator0 Rising-Edge Flag. Must be cleared by software.
0: No Comparator0 Rising Edge has occurred since this flag was last cleared.
1: Comparator0 Rising Edge has occurred.
CP0FIF: Comparator0 Falling-Edge Flag. Must be cleared by software.
0: No Comparator0 Falling-Edge has occurred since this flag was last cleared.
1: Comparator0 Falling-Edge has occurred.
00: Positive Hysteresis Disabled.
01: Positive Hysteresis = 5 mV.
10: Positive Hysteresis = 10 mV.
11: Positive Hysteresis = 20 mV.
00: Negative Hysteresis Disabled.
01: Negative Hysteresis = 5 mV.
10: Negative Hysteresis = 10 mV.
11: Negative Hysteresis = 20 mV.
CP0OUT
Bit6
R
SFR Definition 8.1. CPT0CN: Comparator0 Control
CP0RIF
R/W
Bit5
CP0FIF CP0HYP1 CP0HYP0 CP0HYN1 CP0HYN0 00000000
R/W
Bit4
Rev. 1.7
R/W
Bit3
R/W
Bit2
C8051F330/1/2/3/4/5
R/W
Bit1
R/W
Bit0
SFR Address:
Reset Value
0x9B
67