MC9S08SH8CTG Freescale Semiconductor, MC9S08SH8CTG Datasheet - Page 229

• Manufacturer Part Number: MC9S08SH8CTG
• Description: IC MCU 8BIT 8K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH8CTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 13
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08SH
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO, DEMO9S08SH32, DEMO9S08SH8
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO9S08SH8 - BOARD DEMO FOR MC9S08SH FAM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

15.3
15.3.1
The SPI is disabled in all stop modes, regardless of the settings before executing the STOP instruction.
During either stop1 or stop2 mode, the SPI module will be fully powered down. Upon wake-up from stop1
or stop2 mode, the SPI module will be in the reset state. During stop3 mode, clocks to the SPI module are
halted. No registers are affected. If stop3 is exited with a reset, the SPI will be put into its reset state. If
stop3 is exited with an interrupt, the SPI continues from the state it was in when stop3 was entered.
15.4
The SPI has five 8-bit registers to select SPI options, control baud rate, report SPI status, and for
transmit/receive data.
Refer to the direct-page register summary in the
assignments for all SPI registers. This section refers to registers and control bits only by their names, and
a Freescale-provided equate or header file is used to translate these names into the appropriate absolute
addresses.
15.4.1
This read/write register includes the SPI enable control, interrupt enables, and configuration options.
Freescale Semiconductor
Reset
SPTIE
Field
SPIE
SPE
7
6
5
W
R
Modes of Operation
Register Definition
SPIE
SPI in Stop Modes
SPI Control Register 1 (SPIC1)
SPI Interrupt Enable (for SPRF and MODF) — This is the interrupt enable for SPI receive buffer full (SPRF)
and mode fault (MODF) events.
0 Interrupts from SPRF and MODF inhibited (use polling)
1 When SPRF or MODF is 1, request a hardware interrupt
SPI System Enable — Disabling the SPI halts any transfer that is in progress, clears data buffers, and initializes
internal state machines. SPRF is cleared and SPTEF is set to indicate the SPI transmit data buffer is empty.
0 SPI system inactive
1 SPI system enabled
SPI Transmit Interrupt Enable — This is the interrupt enable bit for SPI transmit buffer empty (SPTEF).
0 Interrupts from SPTEF inhibited (use polling)
1 When SPTEF is 1, hardware interrupt requested
0
7
SPE
0
6
Figure 15-5. SPI Control Register 1 (SPIC1)
MC9S08SH8 MCU Series Data Sheet, Rev. 3
Table 15-1. SPIC1 Field Descriptions
SPTIE
0
5
Memory
MSTR
0
4
Description
chapter of this data sheet for the absolute address
CPOL
3
0
Chapter 15 Serial Peripheral Interface (S08SPIV3)
CPHA
1
2
SSOE
0
1
LSBFE
0
0
229