STM32F102CBT6 STMicroelectronics, STM32F102CBT6 Datasheet - Page 29

• Manufacturer Part Number: STM32F102CBT6
• Description: MCU ARM 32BIT 128KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F102CBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 497-8308

STM32F102x8, STM32F102xB
5.3.5
Table 11.
1. Shortest sampling time can be determined in the application by multiple iterations.
2. Guaranteed by design, not tested in production.
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in
measurement
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code.
Maximum current consumption
The MCU is placed under the following conditions:
●
●
●
●
●
The parameters given in
temperature and V
T
V
Symbol
V
S_vrefint
T
RERINT
Coeff
REFINT
All I/O pins are in input mode with a static value at V
All peripherals are disabled except if it is explicitly mentioned
The Flash access time is adjusted to f
wait state from 24 to 48 MHz)
Prefetch in on (reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
(2)
(2)
(1)
Internal reference voltage
ADC sampling time when reading
the internal reference voltage
Internal reference voltage spread
over the temperature range
Temperature coefficient
Embedded internal reference voltage
scheme.
DD
supply voltage conditions summarized in
Parameter
Table 12
Doc ID 15056 Rev 3
are derived from tests performed under ambient
PCLK1
HCLK
–40 °C < T
V
DD
= f
frequency (0 wait state from 0 to 24 MHz, 1
Conditions
HCLK/2
= 3 V ±10 mV
A
Figure 9: Current consumption
< +85 °C 1.16
, f
DD
PCLK2
or V
Table
= f
SS
Electrical characteristics
Min
HCLK
(no load)
8.
1.20
Typ
5.1
17.1
Max
1.24
100
10
(2)
ppm/
Unit
29/69
mV
°C
µs
V