DSPIC30F6010A-30I/PT Microchip Technology, DSPIC30F6010A-30I/PT Datasheet
DSPIC30F6010A-30I/PT
Specifications of DSPIC30F6010A-30I/PT
Available stocks
Related parts for DSPIC30F6010A-30I/PT
DSPIC30F6010A-30I/PT Summary of contents
Page 1
... DS70157 – “dsPIC30F/33F Programmer’s Reference Manual” • DS70150 – “dsPIC30F6010A/6015 Data Sheet” • DS70046 – “dsPIC30F Family Reference Manual” The exceptions to the specifications in the documents listed above are described in this section. These ...
Page 2
... Motor Control PWM – PWM Counter Register PTMR does not continue counting down after halting code execution in Debug mode. 11. I/O Port – Port Pin Multiplexed with IC1 The port I/O pin multiplexed with the Input Capture 1 (IC1) function cannot be used as a digital input pin when the UART auto-baud feature is enabled ...
Page 3
... Alternatively, make sure that subsequent DISI instructions are called before the DISI counter decrements to zero. © 2008 Microchip Technology Inc. dsPIC30F6010A/6015 2. Module: Output Compare A glitch will be produced on an output compare pin under the following conditions: • The user software initially drives the I/O pin high using the output compare module or a write to the associated PORT register ...
Page 4
... Module: Quadrature Encoder Interface The Index Pulse Reset mode of the QEI does not work properly when used along with count error detection. When counting upwards, the POSCNT register will increment one extra count after the index pulse is received. The extra count will generate a false count error interrupt ...
Page 5
... AD 750 ksps Up to 153. 500 ksps Up to 256. 300 ksps Work around None. © 2008 Microchip Technology Inc. dsPIC30F6010A/6015 R Max V Temperature S DD 500Ω 4.5V to 5.5V -40°C to +85°C 5.0 kΩ 4.5V to 5.5V -40°C to +125°C 5.0 kΩ 3.0V to 5.5V -40°C to +125°C ...
Page 6
... Module: QEI Interrupt Generation The Quadrature Encoder Interface (QEI) module does not generate an interrupt when MAXCNT is set to 0xFFFF and the following events occur: 1. POSCNT underflows from 0x0000 to 0xFFFF. 2. POSCNT stops. 3. POSCNT overflows from 0xFFFF to 0x0000. This sequence of events occurs when the motor is running in one direction, which causes POSCNT to underflow to 0xFFFF ...
Page 7
... GotoSleep( ) function call. This ensures that the device continues executing the correct code sequence after waking up from Sleep mode. Example 2 described above would apply to a dsPIC30F6010A device. ; Ensure flag is reset ; Return from Interrupt Service Routine the function call would ...
Page 8
... Work around 2: Instead of executing a PWRSAV #0 instruction to put the device into Sleep mode, perform a clock switch to the 512 kHz Low-Power RC (LPRC) Oscillator with a 64:1 postscaler mode. This enables the device to operate at 0.002 MIPS, thereby significantly reducing consumption of the device. Similarly, instead of ...
Page 9
... Clear the I C receiver interrupt flag SI2CF back to step 1 to continue receiving incoming data bytes. © 2008 Microchip Technology Inc. dsPIC30F6010A/6015 Work around 2: Use this work around for applications in which the receiver interrupt is required. Assuming that the RBF and the I2COV flags in the I2CSTAT ...
Page 10
... Module: I/O Port – Port Pin Multiplexed with IC1 If the user application enables the auto-baud feature in the UART module, the I/O pin multiplexed with the IC1 (Input Capture) pin cannot be used as a digital input. Work around None. 2 12. Module there are two I ...
Page 11
... For example, if the SDA and SCL pins are shared with the UART and SPI pins, and the UART has higher precedence on the port latch pin. © 2008 Microchip Technology Inc. dsPIC30F6010A/6015 2 C module is that have 2 ...
Page 12
... APPENDIX A: REVISION HISTORY Revision A (01/2006) Original version of the document. Revision B (9/2006) Added silicon issues 1 and 6. Revision C (3/2007) Added silicon issue 7. Revision D (9/2007) Added silicon issue 8 (QEI Interrupt Generation) and 9 (Sleep Mode). Revision E (12/2007) 2 Added silicon issues 10 and 11 (I C), 12 (Motor Control PWM – ...
Page 13
... PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 14
... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2008 Microchip Technology Inc. 01/02/08 ...