PIC16C77-20I/P Microchip Technology, PIC16C77-20I/P Datasheet - Page 62

• Manufacturer Part Number: PIC16C77-20I/P
• Description: IC MCU OTP 8KX14 A/D PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C77-20I/P

• Program Memory Type: OTP
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Operating Supply Voltage: 2.5 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 8-bit
• Controller Family/series: PIC16C
• No. Of I/o's: 33
• Ram Memory Size: 368Byte
• Cpu Speed: 10MHz
• No. Of Timers: 3
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Data Rom Size: 368 B
• Height: 4.95 mm
• Length: 53.21 mm
• Supply Voltage (max): 6 V
• Supply Voltage (min): 4 V
• Width: 14.73 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16C7X
7.3
An 8-bit counter is available as a prescaler for the
Timer0 module, or as a postscaler for the Watchdog
Timer, respectively (Figure 7-6). For simplicity, this
counter is being referred to as “prescaler” throughout
this data sheet. Note that there is only one prescaler
available which is mutually exclusively shared between
the Timer0 module and the Watchdog Timer. Thus, a
prescaler assignment for the Timer0 module means
that there is no prescaler for the Watchdog Timer, and
vice-versa.
FIGURE 7-6:
DS30390E-page 62
RA4/T0CKI
CLKOUT (=Fosc/4)
WDT Enable bit
pin
Watchdog
Timer
Prescaler
Applicable Devices
72 73 73A 74 74A 76 77
Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION<5:0>).
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
T0SE
0
1
PSA
M
U
X
0
1
T0CS
M
U
X
0
8-bit Prescaler
8 - to - 1MUX
Time-out
8
M U X
WDT
1
0
1
PSA
M
U
X
The PSA and PS2:PS0 bits (OPTION<3:0>) determine
the prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g. CLRF 1, MOVWF 1,
BSF
assigned to WDT, a CLRWDT instruction will clear the
prescaler along with the Watchdog Timer. The pres-
caler is not readable or writable.
Note:
PSA
PS2:PS0
1,x....etc.) will clear the prescaler. When
Cycles
SYNC
Writing to TMR0 when the prescaler is
assigned to Timer0 will clear the prescaler
count, but will not change the prescaler
assignment.
2
1997 Microchip Technology Inc.
TMR0 reg
Data Bus
8
Set flag bit T0IF
on Overflow