PIC18F458-I/P Microchip Technology, PIC18F458-I/P Datasheet - Page 109

• Manufacturer Part Number: PIC18F458-I/P
• Description: IC MCU FLASH 16KX16 CAN 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F458-I/P

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 33
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164136, DM163011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: PIC18F458I/P

10.0
In addition to its function as a general I/O port, PORTD
can also operate as an 8-bit wide Parallel Slave Port
(PSP) or microprocessor port. PSP operation is
controlled by the 4 upper bits of the TRISE register
(Register 9-1).
(TRISE<4>) enables PSP operation. In Slave mode,
the port is asynchronously readable and writable by the
external world.
The PSP can directly interface to an 8-bit micro-
processor data bus. The external microprocessor can
read or write the PORTD latch as an 8-bit latch. Setting
the control bit PSPMODE enables the PORTE I/O pins
to become control inputs for the microprocessor port.
When set, port pin RE0 is the RD input, RE1 is the WR
input and RE2 is the CS (chip select) input. For this
functionality, the corresponding data direction bits of
the TRISE register (TRISE<2:0>) must be configured
as inputs (set).
A write to the PSP occurs when both the CS and WR
lines are first detected low. A read from the PSP occurs
when both the CS and RD lines are first detected low.
The timing for the control signals in Write and Read
modes is shown in Figure 10-2 and Figure 10-3,
respectively.
FIGURE 10-2:
© 2006 Microchip Technology Inc.
Note:
PORTD
PSPIF
PARALLEL SLAVE PORT
OBF
CS
WR
RD
IBF
The Parallel Slave Port is only available on
PIC18F4X8 devices.
Setting
Q1
PARALLEL SLAVE PORT WRITE WAVEFORMS
control
Q2
Q3
bit
PSPMODE
Q4
Q1
Q2
FIGURE 10-1:
Q3
Note:
Data Bus
Set Interrupt Flag
PSPIF (PIR1<7>)
WR LATD
or
WR PORTD
RD PORTD
RD LATD
I/O pins have diode protection to V
Q4
Data Latch
Q
D
One bit of PORTD
CK
Q1
EN
PORTD AND PORTE
BLOCK DIAGRAM
(PARALLEL SLAVE PORT)
EN
Q
D
PIC18FXX8
Q2
Chip Select
Read
Write
Q3
DS41159E-page 107
TTL
DD
TTL
TTL
TTL
and V
PORTE pins
Q4
SS
RDx pin
.
CS
WR
RD