PIC16F877T-20/PQ Microchip Technology, PIC16F877T-20/PQ Datasheet - Page 81
![IC MCU FLASH 8KX14 EE 44-MQFP](/photos/6/59/65984/150-44-pqfp_sml.jpg)
PIC16F877T-20/PQ
Manufacturer Part Number
PIC16F877T-20/PQ
Description
IC MCU FLASH 8KX14 EE 44-MQFP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F688T-ISL.pdf
(688 pages)
3.PIC16C770-ISO.pdf
(8 pages)
4.PIC16F873-04SO.pdf
(218 pages)
5.PIC16F873-04SO.pdf
(5 pages)
6.PIC16F873-04SO.pdf
(5 pages)
Specifications of PIC16F877T-20/PQ
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
33
Program Memory Size
14KB (8K x 14)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
44-MQFP, 44-PQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F877T-20/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
9.2.7
Master mode is enabled by setting and clearing the
appropriate SSPM bits in SSPCON and by setting the
SSPEN bit. Once Master mode is enabled, the user
has six options:
• Assert a START condition on SDA and SCL.
• Assert a Repeated START condition on SDA and
• Write to the SSPBUF register initiating transmis-
• Generate a STOP condition on SDA and SCL.
• Configure the I
• Generate an Acknowledge condition at the end of
9.2.7.1
The master device generates all of the serial clock
pulses and the START and STOP conditions. A trans-
fer is ended with a STOP condition or with a Repeated
START condition. Since the Repeated START condi-
tion is also the beginning of the next serial transfer, the
I
In Master Transmitter mode, serial data is output through
SDA, while SCL outputs the serial clock. The first byte
transmitted contains the slave address of the receiving
device (7 bits) and the Read/Write (R/W) bit. In this case,
the R/W bit will be logic '0'. Serial data is transmitted 8 bits
at a time. After each byte is transmitted, an Acknowledge
bit is received. START and STOP conditions are output
to indicate the beginning and the end of a serial transfer.
In Master Receive mode, the first byte transmitted con-
tains the slave address of the transmitting device
(7 bits) and the R/W bit. In this case, the R/W bit will be
logic '1'. Thus, the first byte transmitted is a 7-bit slave
address followed by a '1' to indicate receive bit. Serial
data is received via SDA, while SCL outputs the serial
clock. Serial data is received 8 bits at a time. After each
byte is received, an Acknowledge bit is transmitted.
START and STOP conditions indicate the beginning
and end of transmission.
The baud rate generator used for SPI mode operation
is now used to set the SCL clock frequency for either
100 kHz, 400 kHz, or 1 MHz I
rate generator reload value is contained in the lower 7
bits of the SSPADD register. The baud rate generator
will automatically begin counting on a write to the
2
C bus will not be released.
SCL.
sion of data/address.
a received byte of data.
Note:
2001 Microchip Technology Inc.
The MSSP Module, when configured in I
Master mode, does not allow queueing of
events. For instance, the user is not
allowed to initiate a START condition and
immediately write the SSPBUF register to
initiate transmission before the START
condition is complete. In this case, the
SSPBUF will not be written to and the
WCOL bit will be set, indicating that a write
to the SSPBUF did not occur.
I
2
C MASTER MODE SUPPORT
I
2
C Master Mode Operation
2
C port to receive data.
2
C operation. The baud
2
C
SSPBUF. Once the given operation is complete (i.e.,
transmission of the last data bit is followed by ACK), the
internal clock will automatically stop counting and the
SCL pin will remain in its last state.
A typical transmit sequence would go as follows:
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
k)
l)
9.2.8
In I
located in the lower 7 bits of the SSPADD register
(Figure 9-10). When the BRG is loaded with this value,
the BRG counts down to 0 and stops until another reload
has taken place. The BRG count is decremented twice
per instruction cycle (T
In I
clock arbitration is taking place, the BRG will be reloaded
when the SCL pin is sampled high (Figure 9-11).
FIGURE 9-10:
SSPM3:SSPM0
Note:
2
SSPM3:SSPM0
2
C Master mode, the BRG is reloaded automatically. If
C Master mode, the reload value for the BRG is
User generates a START condition by setting
the START enable bit (SEN) in SSPCON2.
SSPIF is set. The module will wait the required
start time before any other operation takes place.
User loads SSPBUF with address to transmit.
Address is shifted out the SDA pin until all 8 bits
are transmitted.
MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
MSSP module generates an interrupt at the end
of the ninth clock cycle by setting SSPIF.
User loads SSPBUF with eight bits of data.
DATA is shifted out the SDA pin until all 8 bits are
transmitted.
MSSP module shifts in the ACK bit from the
slave device, and writes its value into the
SSPCON2 register (SSPCON2<6>).
MSSP module generates an interrupt at the end
of the ninth clock cycle by setting the SSPIF bit.
User generates a STOP condition by setting the
STOP enable bit, PEN, in SSPCON2.
Interrupt is generated once the STOP condition
is complete.
SCL
Baud Rate = F
BAUD RATE GENERATOR
CLKOUT
CY
BAUD RATE GENERATOR
BLOCK DIAGRAM
), on the Q2 and Q4 clock.
Reload
Control
PIC16F87X
OSC
BRG Down Counter
/ (4 * (SSPADD + 1) )
SSPADD<6:0>
Reload
DS30292C-page 79
F
OSC
/4