DSPIC33FJ256MC510T-I/PF Microchip Technology, DSPIC33FJ256MC510T-I/PF Datasheet - Page 14

• Manufacturer Part Number: DSPIC33FJ256MC510T-I/PF
• Description: IC DSPIC MCU/DSP 256K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ256MC510T-I/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: MA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164323 - MODULE SKT FOR 100TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

26. Module: Interrupt Controller
27. Module: Internal Voltage Regulator
TABLE 5:
DS80447D-page 14
Parameter No. Characteristic
Note 1:
If a clock failure occurs when the device is in Idle
mode, the oscillator failure trap does not vector to
the Trap Service Routine. Instead, the device will
simply wake-up from Idle mode and continue code
execution, if the Fail-Safe Clock Monitor (FSCM) is
enabled.
Work around
Whenever the device wakes up from Idle
(assuming the FSCM is enabled), the user
software should check the state of the OSCFAIL
bit (INTCON1<1>) to determine whether a clock
failure occurred, and then perform the appropriate
clock switch operation. Regardless, the Trap
Service Routine must be included in the user
application.
Affected Silicon Revisions
If a MCLR Reset pulse causes the device to wake-
up from Sleep mode, the device wakes up without
waiting for the on-chip voltage regulator to power-
up. This will subsequently result in a Brown-out
Reset (BOR).
Work around
None.
Affected Silicon Revisions
A2
A2
F20
X
X
2:
AC Characteristics
Frequency calibrated at 25°C and 3.3V. TUN bits can be used to compensate for temperature drift.
Devices set to initial frequency of 7.37 MHz (±2%) at 25°C.
A3
A3
X
X
INTERNAL FRC ACCURACY
A4
A4
X
X
—
Internal FRC Accuracy @ FRC Frequency = 7.37 MHz
Min.
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
-3
Operating temperature -40°C < TA < +85°C for industrial
Typical
—
Max.
+3
28. Module: ECAN
29. Module: Oscillator
The C1RXOVF2 and C2RXOVF2 registers are
non-functional. They are always read back as
0x0000, even when a receive overflow has
occurred.
Work around
None.
Affected Silicon Revisions
The device does not meet the internal FRC
accuracy specifications in the data sheet (Table
23-18 of the “PIC24H Family Data Sheet”
(DS70175)). The actual accuracy specifications
are shown in Table 5.
Work around
None.
Affected Silicon Revisions
A2
A2
Units
X
X
%
A3
A3
X
X
-40°C < TA < +85°C V
A4
A4
X
X
(1,2)
© 2010 Microchip Technology Inc.
Conditions
DD
= 3.0-3.6V