PIC24FJ256GA110T-I/PF Microchip Technology, PIC24FJ256GA110T-I/PF Datasheet - Page 32

• Manufacturer Part Number: PIC24FJ256GA110T-I/PF
• Description: IC PIC MCU FLASH 256K100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256GA110T-I/PF

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (85.5K x 24)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: MA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC164323 - MODULE SKT FOR 100TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC24FJ256GA110T-I/PFTR

PIC24FJXXXDA1/DA2/GB2/GA3
4.6
4.6.1
The PIC24FJXXXDA1/DA2/GB2/GA3 families have
Configuration bits stored in the last four locations of
implemented program memory (see
tions). These bits can be set or cleared to select various
device configurations. There are two types of Configura-
tion bits: system operation bits and code-protect bits. The
system operation bits determine the power-on settings
for system level components, such as the oscillator and
Watchdog Timer. The code-protect bits prevent program
memory from being read and written to.
TABLE 4-2:
DS39970B-page 32
ALTPMP
ALTVREF
DEBUG
FCKSM<1:0>
FNOSC<2:0>
FWDTEN
FWPSA
GCP
Note 1:
2:
3:
Configuration Bits Programming
Bit Field
Bits<23-16> should be programmed to a value of 0x00 to ensure that accidental program execution of any
of the Configuration Words would be interpreted as a NOP opcode.
The JTAGEN bit can be modified using only In-Circuit Serial Programming™ (ICSP™).
Irrespective of the WPCFG status, if WPEND = 1 or if WPFP corresponds to the Configuration Words
page, the Configuration Words page will be protected
OVERVIEW
PIC24FJXXXDA1/DA2/GB2 CONFIGURATION BITS DESCRIPTION
CW2<10:8>
Register
CW2<7:6>
CW3<12>
CW1<13>
CW1<11>
CW1<5>
CW1<7>
CW1<4>
Table 2-2
(1)
Alternate PMP Pin Mapping bit
1 = EPMP is in Default Location mode
0 = EPMP is in Alternate Location mode
Alternate V
1 = V
0 = V
Background Debugger Enable bit
1 = Device resets into Operational mode
0 = Device resets into Debug mode
Clock Switching and Fail-Safe Clock Monitor (FSCM) Configuration bits
1x = Clock switching and Fail-Safe Clock Monitor are disabled
01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled
00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled
Initial Oscillator Source Selection bits
111 = Fast RC Oscillator with Postscaler module (FRCDIV)
110 = Reserved
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL)
010 = Primary (XT, HS, EC) Oscillator
001 = Fast RC Oscillator with Postscaler and PLL module (FRCPLL)
000 = Fast RC (FRC) Oscillator
Watchdog Timer Enable bit
1 = Watchdog Timer is enabled
0 = Watchdog Timer is disabled
Watchdog Timer Prescaler bit
1 = WDT prescaler ratio of 1:128
0 = WDT prescaler ratio of 1:32
General Segment Program Memory Code Protection bit
1 = Code protection is disabled
0 = Code protection is enabled for the entire program memory space
for loca-
REF
REF
is on a default pin (V
is on an alternate pin (V
REF
Location Enable bit
Table 4-2
PIC24FJXXXDA1/DA2/GB2 Configuration bits in the
Flash Configuration Words.
Note:
Description
REF
Although not implemented with a specific
function, the bit at CW1<15> must always
be maintained as ‘0’ to ensure device
functionality, regardless of the settings of
other Configuration bits.
provides
REF
+ on RA9 and V
+ on RB0 and V
 2010 Microchip Technology Inc.
the
descriptions
REF
REF
- on RA10)
- on RB1)
for
the