PIC18LF4420-I/PT Microchip Technology, PIC18LF4420-I/PT Datasheet - Page 20

• Manufacturer Part Number: PIC18LF4420-I/PT
• Description: IC MCU FLASH 8KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF4420-I/PT

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 36
• Interface Type: I2C/SPI/USART
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F2XXX/4XXX FAMILY
3.3
Data EEPROM is accessed one byte at a time via an
Address Pointer (register pair: EEADRH:EEADR) and
a data latch (EEDATA). Data EEPROM is written by
loading EEADRH:EEADR with the desired memory
location, EEDATA, with the data to be written and initi-
ating a memory write by appropriately configuring the
EECON1 register. A byte write automatically erases the
location and writes the new data (erase-before-write).
When using the EECON1 register to perform a data
EEPROM write, both the EEPGD and CFGS bits must
be cleared (EECON1<7:6> = 00). The WREN bit must
be set (EECON1<2> = 1) to enable writes of any sort
and this must be done prior to initiating a write
sequence. The write sequence is initiated by setting the
WR bit (EECON1<1> = 1).
The write begins on the falling edge of the 4th PGC
after the WR bit is set. It ends when the WR bit is
cleared by hardware.
FIGURE 3-7:
DS39622L-page 20
PIC18F2410
PIC18F2450
PIC18F2510
PIC18F2515
PIC18F2610
Note:
PGC
PGD
Poll WR bit
Data EEPROM Programming
4-Bit Command
1
0
Data EEPROM programming is not
available on the the following devices:
2
0
3
0
4
0
PGC
PGD
P5
DATA EEPROM WRITE TIMING
BSF EECON1, WR
1
4-Bit Command
PIC18F4410
PIC18F4450
PIC18F4510
PIC18F4515
PIC18F4610
2
1
0
2
0
15 16
3
0
4
0
P5A
P5
MOVF EECON1, W, 0
1
2
PGD = Input
PGD = Input
15 16
P5A
4-Bit Command
1
Poll WR bit, Repeat until Clear
0
After the programming sequence terminates, PGC must
still be held low for the time specified by Parameter P10
to allow high-voltage discharge of the memory array.
FIGURE 3-6:
2
0
3
0
P11A
(see below)
4
0
P5
MOVWF TABLAT
1
No
2
15 16
PROGRAM DATA FLOW
Enable Write
Set Address
Start Write
Sequence
 2010 Microchip Technology Inc.
Set Data
Done?
WR bit
clear?
Done
Start
P5A
Yes
Yes
(see Figure 4-4)
PGD = Output
Shift Out Data
No
P10
16-Bit Data
Payload
1
n
2
n