AT91M40800-33AU-999 Atmel, AT91M40800-33AU-999 Datasheet - Page 8

• Manufacturer Part Number: AT91M40800-33AU-999
• Description: IC MCU 32BIT RISC 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91M40800-33AU-999

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: EBI, USART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

7.5.2
7.6
7.6.1
7.6.2
8
Memory Controller
AT91M40800
JTAG/ICE Debug
Internal Memories
Boot Mode Select
To enter Tri-state mode, the pin NTRI must be held low during the last 10 clock cycles before the
rising edge of NRST. For normal operation the pin NTRI must be held high during reset by a
resistor of up to 400K Ohm.
NTRI is multiplexed with I/O line P21 and USART1 serial data transmit line TXD1.
Standard RS232 drivers generally contain internal 400K Ohm pull-up resistors. If TXD1 is con-
nected to a device not including this pull-up, the user must make sure that a high level is tied on
NTRI while NRST is asserted.
ARM Standard Embedded In-circuit Emulation is supported via the JTAG/ICE port. The pins
TDI, TDO, TCK and TMS are dedicated to this debug function and can be connected to a host
computer via the external ICE interface.
In ICE Debug mode, the ARM7TDMI core responds with a non-JTAG chip ID that identifies the
microcontroller. This is not fully IEEE
The ARM7TDMI processor address space is 4G bytes. The memory controller decodes the
internal 32-bit address bus and defines three address spaces:
In any of these address spaces, the ARM7TDMI operates in Little-Endian mode only.
The AT91M40800 microcontroller integrates 8K bytes of internal SRAM. All internal memories
are 32 bits wide and single-clock cycle accessible. Byte (8-bit), half-word (16-bit) or word (32-bit)
accesses are supported and are executed within one cycle. Fetching Thumb or ARM instruc-
tions is supported and internal memory can store twice as many Thumb instructions as ARM
ones.
The SRAM is mapped at address 0x0 (after the remap command), allowing ARM7TDMI excep-
tion vectors between 0x0 and 0x20 to be modified by the software. The rest of the bank can be
used for stack allocation (to speed up context saving and restoring) or as data and program stor-
age for critical algorithms.
The ARM reset vector is at address 0x0. After the NRST line is released, the ARM7TDMI exe-
cutes the instruction stored at this address. This means that this address must be mapped in
nonvolatile memory after the reset.
The input level on the BMS pin during the last 10 clock cycles before the rising edge of the
NRST selects the type of boot memory (see
• Internal memories in the four lowest megabytes
• Middle space reserved for the external devices (memory or peripherals) controlled by the EBI
• Internal peripherals in the four highest megabytes
®
1149.1 compliant.
Table
7-1).
1348FS–ATARM–13-Apr-06