PIC16C55-XT/SO Microchip Technology, PIC16C55-XT/SO Datasheet - Page 42

• Manufacturer Part Number: PIC16C55-XT/SO
• Description: IC MCU OTP 512X12 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C55-XT/SO

• Core Size: 8-Bit
• Program Memory Size: 768B (512 x 12)
• Oscillator Type: External
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 20
• Program Memory Type: OTP
• Ram Size: 24 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6.25 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC16C
• No. Of I/o's: 20
• Ram Memory Size: 24Byte
• Cpu Speed: 40MHz
• No. Of Timers: 1
• Digital Ic: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL309-1073 - ADAPTER 28-SOIC TO 28-SOIC309-1024 - ADAPTER 28-SOIC TO 28-DIP309-1023 - ADAPTER 28-SOIC TO 28-DIP309-1011 - ADAPTER 18-SOIC TO 18-DIP309-1010 - ADAPTER 18-SOIC TO 18-DIPAC164002 - MODULE SKT PROMATEII 18/28SOIC
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16C5X
8.2
An 8-bit counter is available as a prescaler for the
Timer0 module, or as a postscaler for the Watchdog
Timer (WDT), respectively (Section 9.2.1). For simplic-
ity, this counter is being referred to as “prescaler”
throughout this data sheet. Note that the prescaler may
be used by either the Timer0 module or the WDT, but
not both. Thus, a prescaler assignment for the Timer0
module means that there is no prescaler for the WDT,
and vice-versa.
The PSA and PS<2:0> bits (OPTION<3:0>) determine
prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing
MOVWF 1, BSF 1,x, etc.) will clear the prescaler.
When assigned to WDT, a CLRWDT instruction will clear
the prescaler along with the WDT. The prescaler is nei-
ther readable nor writable. On a RESET, the prescaler
contains all '0's.
8.2.1
The prescaler assignment is fully under software con-
trol (i.e., it can be changed “on the fly” during program
execution). To avoid an unintended device RESET, the
following instruction sequence (Example 8-1) must be
executed when changing the prescaler assignment
from Timer0 to the WDT.
DS30453D-page 40
to
Prescaler
SWITCHING PRESCALER
ASSIGNMENT
the
TMR0
register
(e.g.,
CLRF 1,
Preliminary
EXAMPLE 8-1:
To change prescaler from the WDT to the Timer0 mod-
ule, use the sequence shown in Example 8-2. This
sequence must be used even if the WDT is disabled. A
CLRWDT instruction should be executed before switch-
ing the prescaler.
EXAMPLE 8-2:
CLRWDT
MOVLW
OPTION
CLRWDT
CLRF
MOVLW
OPTION
CLRWDT
MOVLW
OPTION
B'xxxx0xxx'
TMR0
B'00xx1111’ ;Last 3 instructions in
B'00xx1xxx’ ;Set Prescaler to
(TIMER0 WDT)
(WDT TIMER0)
CHANGING PRESCALER
CHANGING PRESCALER
2002 Microchip Technology Inc.
;are required only if
;Clear WDT
;Clear TMR0 & Prescaler
;PS<2:0> are 000 or
;001
;Clear WDT and
;prescaler
;Select TMR0, new
;prescale value and
;clock source
;desired
;desired WDT rate
this example