DSPIC33FJ12MC202-I/ML Microchip Technology, DSPIC33FJ12MC202-I/ML Datasheet - Page 4

• Manufacturer Part Number: DSPIC33FJ12MC202-I/ML
• Description: IC DSPIC MCU/DSP 12K 28QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ12MC202-I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 12KB (12K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: I2C, JTAG, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 12KB
• Supply Voltage Range: 3V To 3.6V
• Package: 28QFN EP
• Device Core: dsPIC
• Family Name: dSPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit|6-chx12-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164336 - MODULE SOCKET FOR PM3 28/44QFNDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Silicon Errata Issues
1. Module: JTAG
2. Module: UART
3. Module: UART
DS80461E-page 4
Note:
JTAG programming does not work.
Work around
None.
Affected Silicon Revisions
UART receptions may be corrupted if the Baud
Rate Generator is set up for 4x mode (BRGH = 1).
Work around
Use the 16x baud rate option (BRGH = 0) and
adjust the baud rate accordingly.
Affected Silicon Revisions
The auto-baud feature may not calculate the correct
baud rate when the High Baud Rate Enable bit,
BRGH, is set. With the BRGH bit set, the baud rate
calculation used is the same as BRG = 0.
Work around
If the auto-baud feature is needed, use the Low
Baud Rate mode by clearing the BRGH bit.
Affected Silicon Revisions
A2
A2
A2
X
X
X
This document summarizes all silicon
errata issues from all revisions of silicon,
previous as well as current. Only the
issues indicated by the shaded column in
the following tables apply to the current
silicon revision (A5).
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
A5
A5
A5
X
X
X
4. Module: UART
5. Module: UART
6. Module: UART
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
Work around
To prevent the Sync Break character from being
loaded into the FIFO, load the UxBRG register with
either 0x0000 or 0xFFFF prior to enabling the
auto-baud feature (ABAUD = 1).
Affected Silicon Revisions
The auto-baud feature may miscalculate certain
baud rate and clock speed combinations, resulting
in a BRG value that is greater than or less than the
expected value by 1. This may result in reception
or transmission failures.
Work around
Test the auto-baud rate at various clock speed and
baud rate combinations that would be used in an
application. If an inaccurate BRG value is
generated, manually correct the baud rate in user
software.
Affected Silicon Revisions
When an auto-baud is detected, the receive
interrupt may occur twice. The first interrupt occurs
at the beginning of the Start bit and the second
after reception of the Sync field character.
Work around
If an extra interrupt is detected, ignore the
additional interrupt.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
© 2010 Microchip Technology Inc.
A5
A5
A5
X
X
X