PIC18F8410-E/PT Microchip Technology, PIC18F8410-E/PT Datasheet - Page 179

• Manufacturer Part Number: PIC18F8410-E/PT
• Description: IC PIC MCU FLASH 16KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F8410-E/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TFQFP
• For Use With: XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

REGISTER 17-2:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3-0
Note 1:
WCOL
R/W-0
2:
3:
In Master mode, the overflow bit is not set, since each new reception (and transmission) is initiated by
writing to the SSPBUF register.
When enabled, these pins must be properly configured as inputs or outputs.
Bit combinations not specifically listed here are either reserved or implemented in I
WCOL: Write Collision Detect bit (Transmit mode only)
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in
0 = No collision
SSPOV: Receive Overflow Indicator bit
SPI Slave mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of
0 = No overflow
SSPEN: Master Synchronous Serial Port Enable bit
1 = Enables serial port and configures SCK, SDO, SDI and SS as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
SSPM<3:0>: Master Synchronous Serial Port Mode Select bits
0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin
0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled
0011 = SPI Master mode, clock = TMR2 output/2
0010 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0000 = SPI Master mode, clock = F
SSPOV
R/W-0
software)
overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read
the SSPBUF, even if only transmitting data, to avoid setting overflow (must be cleared in
software).
SSPCON1: MSSP CONTROL REGISTER 1 (SPI MODE)
(1)
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
(2)
PIC18F6310/6410/8310/8410
R/W-0
CKP
OSC
OSC
OSC
(1)
/64
/16
/4
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
(2)
(3)
SSPM2
R/W-0
(3)
(3)
x = Bit is unknown
SSPM1
R/W-0
2
C™ mode only.
(3)
DS39635C-page 179
SSPM0
R/W-0
bit 0
(3)