ATMEGA328-PU Atmel, ATMEGA328-PU Datasheet - Page 305
![IC MCU AVR 32K FLASH 28PDIP](/photos/7/21/72189/453-28-dip_sml.jpg)
ATMEGA328-PU
Manufacturer Part Number
ATMEGA328-PU
Description
IC MCU AVR 32K FLASH 28PDIP
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA328-PU
Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
32KB (16K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Processor Series
ATMEGA328x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
2 KB
Interface Type
2-Wire, SPI, USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
23
Number Of Timers
3
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 6 Channel
On-chip Dac
10 bit, 6 Channel
Operating Temperature Range
- 40 C to + 85 C
Processor To Be Evaluated
ATMEGA328
Supply Current (max)
0.2 mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA328-PU
Manufacturer:
USB
Quantity:
3 200
- Current page: 305 of 566
- Download datasheet (23Mb)
27.7.3
27.7.4
8271C–AVR–08/10
Chip Erase
Programming the Flash
The Chip Erase will erase the Flash and EEPROM
not reset until the program memory has been completely erased. The Fuse bits are not
changed. A Chip Erase must be performed before the Flash and/or EEPROM are
reprogrammed.
Note:
Load Command “Chip Erase”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “1000 0000”. This is the command for Chip Erase.
4. Give XTAL1 a positive pulse. This loads the command.
5. Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low.
6. Wait until RDY/BSY goes high before loading a new command.
The Flash is organized in pages, see
the program data is latched into a page buffer. This allows one page of program data to be pro-
grammed simultaneously. The following procedure describes how to program the entire Flash
memory:
A. Load Command “Write Flash”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “0001 0000”. This is the command for Write Flash.
4. Give XTAL1 a positive pulse. This loads the command.
B. Load Address Low byte
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS1 to “0”. This selects low address.
3. Set DATA = Address low byte (0x00 - 0xFF).
4. Give XTAL1 a positive pulse. This loads the address low byte.
C. Load Data Low Byte
1. Set XA1, XA0 to “01”. This enables data loading.
2. Set DATA = Data low byte (0x00 - 0xFF).
3. Give XTAL1 a positive pulse. This loads the data byte.
D. Load Data High Byte
1. Set BS1 to “1”. This selects high data byte.
2. Set XA1, XA0 to “01”. This enables data loading.
3. Set DATA = Data high byte (0x00 - 0xFF).
4. Give XTAL1 a positive pulse. This loads the data byte.
E. Latch Data
1. Set BS1 to “1”. This selects high data byte.
2. Give PAGEL a positive pulse. This latches the data bytes. (See
F. Repeat B through E until the entire buffer is filled or until all data within the page is loaded.
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
waveforms)
1. The EEPRPOM memory is preserved during Chip Erase if the EESAVE Fuse is programmed.
Table 27-11 on page
(1)
memories plus Lock bits. The Lock bits are
301. When programming the Flash,
Figure 27-3
for signal
305
Related parts for ATMEGA328-PU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega32](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA32-8AU](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA32-16MU](/photos/12/13/121316/313-44-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ 5V 44-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16PU](/photos/6/70/67049/453-40-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ 5V 40DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AU](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ 5V 44TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16PI](/photos/6/70/67049/453-40-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ IND 40-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AI](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ IND 44-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 32KB FLASH 16MHZ 44TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16MUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 32KB FLASH 16MHZ 44QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AQ](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
MCU AVR 32K FLASH 16MHZ 44-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16PC](/photos/6/70/67049/453-40-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ COM 40-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16MC](/photos/12/13/121316/313-44-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ COM 44-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AC](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ COM 44-TQFP
Manufacturer:
Atmel
Datasheet: