PIC16C72AT-20I/SO Microchip Technology, PIC16C72AT-20I/SO Datasheet - Page 21
![IC MCU OTP 2KX14 A/D PWM 28SOIC](/photos/6/59/65909/150-28-soic_sml.jpg)
PIC16C72AT-20I/SO
Manufacturer Part Number
PIC16C72AT-20I/SO
Description
IC MCU OTP 2KX14 A/D PWM 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C62B-04SO.pdf
(120 pages)
4.PIC16C72A-04SP.pdf
(6 pages)
Specifications of PIC16C72AT-20I/SO
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16C72AT-20I/SO
Manufacturer:
MIC
Quantity:
20 000
3.2
PORTB is an 8-bit wide bi-directional port. The corre-
sponding data direction register is TRISB. Setting a
TRISB bit (=1) will make the corresponding PORTB pin
an input, (i.e., put the corresponding output driver in a
hi-impedance mode). Clearing a TRISB bit (=0) will
make the corresponding PORTB pin an output, (i.e.,
put the contents of the output latch on the selected pin).
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is per-
formed by clearing bit RBPU (OPTION_REG<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are dis-
abled on a Power-on Reset.
FIGURE 3-3:
Data Bus
WR TRIS
WR Port
RBPU
RB0/INT
1999 Microchip Technology Inc.
Note 1: I/O pins have diode protection to V
(2)
2: To enable weak pull-ups, set the appropriate TRIS bit(s)
PORTB and the TRISB Register
and clear the RBPU bit (OPTION_REG<7>).
BLOCK DIAGRAM OF
RB3:RB0 PINS
RD TRIS
RD Port
TRIS Latch
Data Latch
D
D
CK
CK
Schmitt Trigger
Buffer
Q
Q
Q
DD
and V
EN
TTL
Input
Buffer
D
SS
V
.
P
RD Port
DD
weak
pull-up
I/O
pin
Preliminary
(1)
Four of PORTB’s pins, RB7:RB4, have an interrupt on
change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e. any RB7:RB4 pin con-
figured as an output is excluded from the interrupt on
change comparison). The input pins (of RB7:RB4) are
compared with the old value latched on the last read of
PORTB. The “mismatch” outputs of RB7:RB4 are
OR’ed together to generate the RB Port Change Inter-
rupt with flag bit RBIF (INTCON<0>).
This interrupt can wake the device from SLEEP. The
user, in the interrupt service routine, can clear the inter-
rupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt on change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt on change
feature. Polling of PORTB is not recommended while
using the interrupt on change feature.
RB0/INT is an external interupt pin and is configured
using the INTEDG bit (OPTION_REG<6>). RB0/INT is
discussed in detail in Section 10.10.1.
FIGURE 3-4:
Data Bus
WR TRIS
WR Port
RBPU
RB7:RB6 in serial programming mode
Note 1: I/O pins have diode protection to V
Set RBIF
From other
RB7:RB4 pins
Any read or write of PORTB. This will end the
mismatch condition.
Clear flag bit RBIF.
2: To enable weak pull-ups, set the appropriate TRIS bit(s)
(2)
and clear the RBPU bit (OPTION_REG<7>).
PIC16C62B/72A
RD TRIS
RD Port
Data Latch
TRIS Latch
D
D
BLOCK DIAGRAM OF
RB7:RB4 PINS
CK
CK
Q
Q
Q
Q
Latch
DD
EN
EN
DS35008B-page 21
D
D
TTL
Input
Buffer
and V
V
SS
P
DD
.
weak
pull-up
RD Port
Buffer
I/O
pin
Q1
Q3
(1)
ST