PIC16C62B-20I/SO Microchip Technology, PIC16C62B-20I/SO Datasheet - Page 34
![IC MCU OTP 2KX14 PWM 28SOIC](/photos/6/59/65909/150-28-soic_sml.jpg)
PIC16C62B-20I/SO
Manufacturer Part Number
PIC16C62B-20I/SO
Description
IC MCU OTP 2KX14 PWM 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F818-ISO.pdf
(6 pages)
2.PIC16C62B-04SO.pdf
(120 pages)
3.PIC16C62B-04SO.pdf
(5 pages)
4.PIC16C62A-04SP.pdf
(337 pages)
Specifications of PIC16C62B-20I/SO
Core Size
8-Bit
Program Memory Size
3.5KB (2K x 14)
Oscillator Type
External
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Controller Family/series
PIC16C
No. Of I/o's
22
Ram Memory Size
128Byte
Cpu Speed
20MHz
No. Of Timers
3
No. Of Pwm
RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16C62B-20I/SO
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
PIC16C62B-20I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC16C62B/72A
7.1
In Capture mode, CCPR1H:CCPR1L captures the
16-bit value of the TMR1 register, when an event
occurs on pin RC2/CCP1. An event is defined as:
• every falling edge
• every rising edge
• every 4th rising edge
• every 16th rising edge
An event is selected by control bits CCP1M3:CCP1M0
(CCP1CON<3:0>). When a capture is made, the inter-
rupt request flag bit ,CCP1IF (PIR1<2>), is set. It must
be cleared in software. If another capture occurs before
the value in register CCPR1 is read, the old captured
value will be lost.
FIGURE 7-1:
7.1.1
In Capture mode, the RC2/CCP1 pin should be config-
ured as an input by setting the TRISC<2> bit.
7.1.2
Timer1 must be running in timer mode or synchronized
counter mode for the CCP module to use the capture
feature. In asynchronous counter mode, the capture
operation may not work consistently.
7.1.3
When the Capture mode is changed, a false capture
interrupt may be generated. The user should clear
CCP1IE (PIE1<2>) before changing the capture mode
to avoid false interrupts. Clear the interrupt flag bit,
CCP1IE before setting CCP1IE.
DS35008B-page 34
RC2/CCP1
Pin
Note:
Capture Mode
CCP PIN CONFIGURATION
TIMER1 MODE SELECTION
SOFTWARE INTERRUPT
If the RC2/CCP1 is configured as an out-
put, a write to the port can cause a capture
condition.
edge detect
Q’s
Prescaler
1, 4, 16
and
CCP1CON<3:0>
CAPTURE MODE OPERATION
BLOCK DIAGRAM
Set flag bit CCP1IF
(PIR1<2>)
Capture
Enable
CCPR1H
TMR1H
CCPR1L
TMR1L
Preliminary
7.1.4
There are four prescaler settings, specified by bits
CCP1M3:CCP1M0. Whenever the CCP module is
turned off, or the CCP module is not in capture mode,
the prescaler counter is cleared. This means that any
reset will clear the prescaler counter.
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared, therefore the first capture may be from
a non-zero prescaler. Example 7-1 shows the recom-
mended method for switching between capture pres-
calers. This example also clears the prescaler counter
and will not generate the “false” interrupt.
EXAMPLE 7-1:
CLRF
MOVLW
MOVWF
CCP1CON
NEW_CAPT_PS
CCP1CON
CCP PRESCALER
CHANGING BETWEEN
CAPTURE PRESCALERS
;Turn CCP module off
;Load the W reg with
; the new prescaler
; mode value and CCP ON
;Load CCP1CON with this
; value
1999 Microchip Technology Inc.