PIC16C433-E/SO Microchip Technology, PIC16C433-E/SO Datasheet - Page 11
![IC MCU CMOS 8BIT 10MHZ 2K 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
PIC16C433-E/SO
Manufacturer Part Number
PIC16C433-E/SO
Description
IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Specifications of PIC16C433-E/SO
Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Connectivity
LIN (Local Interconnect Network)
Peripherals
POR, WDT
Number Of I /o
5
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 4x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
18-SOIC (7.5mm Width)
For Use With
AC164030 - MODULE SKT PROMATEII 28DIP/SOIC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
TABLE 3-1:
2002 Microchip Technology Inc.
GP0/AN0
GP1/AN1/V
GP2/T0CKI/AN2/INT
GP3/MCLR/V
GP4/OSC2/AN3/CLKOUT
GP5/OSC1/CLKIN
LIN
V
BACT
V
V
AV
AV
Legend: I = Input, O = Output, I/O = Input/Output, P = Power, — = not used, TTL = TTL input,
BAT
DD
SS
DD
SS
ST = Schmitt Trigger input, OD = Open Drain
Name
REF
PP
PIC16C433 PINOUT DESCRIPTION
DIP Pin #
3,14,16
13
12
18
17
15
11
8
7
6
1
4
5
I/O/P
Type
I/O
I/O
I/O
I/O
I/O
I/O
O
P
P
P
P
P
I
TTL/ST Bi-directional I/O port/serial programming data/analog input
TTL/ST Bi-directional I/O port/serial programming clock/analog
TTL/ST Input port/Master Clear (Reset) input/programming voltage
TTL/ST Bi-directional IO port/oscillator crystal input/external clock
HV/OD High voltage bi-directional bus interface.
Buffer
Type
TTL
TTL
ST
Preliminary
—
—
—
—
—
0. Can be software programmed for internal weak pull-up
and interrupt-on-pin change. This buffer is a Schmitt Trig-
ger input when used in Serial Programming mode.
input 1/voltage reference. Can be software programmed for
internal weak pull-up and interrupt-on-pin change. This
buffer is a Schmitt Trigger input when used in Serial Pro-
gramming mode.
Bi-directional I/O port/analog input 2. Can be configured as
T0CKI or external interrupt.
input. When configured as MCLR, this pin is an active low
RESET to the device. Voltage on MCLR/V
exceed V
ware programmed for internal weak pull-up and interrupt-
on-pin change. Weak pull-up always on if configured as
MCLR. This buffer is Schmitt Trigger when in MCLR mode.
Bi-directional I/O port/oscillator crystal output/analog input
3. Connections to crystal or resonator in Crystal Oscillator
mode (HS, XT and LP modes only, GPIO in other modes).
In EXTRC and INTRC modes, the pin output can be config-
ured to CLKOUT, which has 1/4 the frequency of OSC1 and
denotes the instruction cycle rate.
source input (GPIO in INTRC mode only, OSC1 in all other
oscillator modes). Schmitt Trigger input for EXTRC Oscilla-
tor mode.
Battery input voltage.
Bus activity output pin. It is a CMOS-levels representation
of the LIN pin.
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Analog positive supply.
Analog ground.
DD
during normal device operation. Can be soft-
Description
PIC16C433
PP
DS41139B-page 9
must not