PIC16C433-E/SO Microchip Technology, PIC16C433-E/SO Datasheet - Page 7

IC MCU CMOS 8BIT 10MHZ 2K 18SOIC

PIC16C433-E/SO

Manufacturer Part Number
PIC16C433-E/SO
Description
IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets

Specifications of PIC16C433-E/SO

Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Connectivity
LIN (Local Interconnect Network)
Peripherals
POR, WDT
Number Of I /o
5
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 4x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
18-SOIC (7.5mm Width)
For Use With
AC164030 - MODULE SKT PROMATEII 28DIP/SOIC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
The Electrical Specifications have been changed to
include the maximum current sunk by LIN and BACT
pins, as shown in the following table in Section 12.0 of
the PIC16C433 Data Sheet.
12.0 Electrical Specifications for PIC16C433
Absolute Maximum Ratings
Ambient Temperature under bias .............................................................................................................. -40 to +125 C
Storage Temperature ................................................................................................................................ -65 to +150 C
Voltage on any pin with respect to V
Voltage on V
Voltage on RA4 with respect to V
Voltage on MCLR with respect to V
Voltage on RA4 with respect to V
Total power Dissipation (Note 1)...............................................................................................................................1.0W
Maximum Current out of V
Maximum Current into V
Input Clamp Current, I
Output Clamp Current, I
Maximum Output Current sunk by any I/O pin ........................................................................................................25 mA
Maximum Output Current sourced by any I/O pin...................................................................................................25 mA
Maximum Current sunk by GPIO ..........................................................................................................................200 mA
Maximum Current sourced by GPIO .....................................................................................................................200 mA
Maximum Current sunk by LIN..............................................................................................................................200 mA
Maximum Current sunk by BACT...........................................................................................................................1.8 mA
† NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions, above
those indicated in the operation listings of this specification, is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
Note 1: Power dissipation is calculated as follows: P
2001 Microchip Technology Inc.
2: Voltage spikes below V
Thus, a series resistor of 50-100 should be used when applying a "low" level to the MCLR pin, rather than
pulling this pin directly to V
DD
with respect to V
IK
OK
DD
(V
SS
I
(V
pin .............................................................................................................................250 mA
<0 or V
O
pin ..........................................................................................................................300 mA
(†)
<0 or V
SS
SS
SS
SS
I
...........................................................................................................................8.5V
...........................................................................................................................8.5V
SS
> V
SS
................................................................................................................ 0 to +7.0V
(Note 2) .................................................................................................0 to +14V
SS
O
(except V
at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.
DD
>V
.
)
DD
)
DD
and MCLR) .......................................................-0.6V to V
DIS
= V
DD
x {I
DD
-
I
OH
} +
{(V
DD
PIC16C433
-V
OH
) x I
OH
DS80116B-page 7
} + (V
DD
O
l x I
20 mA
20 mA
+0.6V
OL
)

Related parts for PIC16C433-E/SO