PIC16LC433-I/P Microchip Technology, PIC16LC433-I/P Datasheet - Page 89

• Manufacturer Part Number: PIC16LC433-I/P
• Description: IC MCU CMOS 8BIT 10MHZ 2K 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC433-I/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: LIN (Local Interconnect Network)
• Peripherals: POR, WDT
• Number Of I /o: 6
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

12.1
PIC16C433
D001
D001A
D002
D003
D004
D010
D010C
D010A
D020
D021
D021B
D022
D028
Note 1: This is the limit to which V
Parm
2001 Microchip Technology Inc.
No.
(Industrial, Extended)
†
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
3: For EXTRC osc configuration, current through R
4: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
5: INTRC calibration value is for 4MHz nominal at 5V, 25°C.
*
DC Characteristics
V
V
V
V
S
I
I
F
These parameters are characterized but not tested.
loading, oscillator type, bus rate, internal code execution pattern and temperature, also have an impact on the current
consumption.
a)
b)
by the formula:
Ir = V
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
Data in Typical (“Typ”) column is based on characterization results at 25 C unless otherwise stated.
These parameters are for design guidance only and are not tested.
DD
PD
Sym
I
I
OSC
DD
BAT
DR
POR
VDD
WDT
EE
The test conditions for all I
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
MCLR = V
For standby current measurements, the conditions are the same, except that the device is in
SLEEP mode.
DD
/2R
Supply Voltage
Operating Battery Voltage
RAM Data Retention
Voltage (Note 1)
V
Power-on Reset
V
Power-on Reset
Supply Current (Note 2)
Power-down Current (Note 4)
Watchdog Timer Current
Supply Current (Note 2)
During read/write to EEPROM
peripheral
LP Oscillator Operating
Frequency
INTRC/EXTRC Oscillator
Operating Frequency
XT Oscillator Operating
Frequency
HS Oscillator Operating
Frequency
DD
DD
EXT
Start Voltage to ensure
Rise Rate to ensure
DD
(mA) with R
Characteristic
; WDT disabled.
DD
EXT
can be lowered in SLEEP mode without losing RAM data.
DD
in kOhm.
measurements in active operation mode are:
Advance Information
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0.05*
Min
3.0
8.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0
0
0
EXT
Typ†
13.8
0.25
0.25
1.5*
V
1.2
1.2
2.2
0.5
0.8
2.2
2.2
0.1
19
19
32
2
3
4
SS
is not included. The current through the resistor can be estimated
Max Units
200
4
5.5
2.5
2.5
0.2
18
29
37
60
14
16
10
11
8
6
7
8
9
5
6
4
(5)
V/ms See section on Power-on Reset for details
MHz
MHz
MHz
kHz
mA
mA
mA
mA
V
V
V
V
A
A
A
A
A
A
A
A
A
A
A
A
–40°C
–40°C
Device in SLEEP mode
See section on Power-on Reset for details
F
XT and EXTRC mode (Note 3)
F
INTRC mode (Note 5)
F
HS mode
F
LP mode, Commercial Temperature
F
LP mode, Industrial Temperature
F
LP mode, Extended Temperature
V
V
V
V
V
V
V
V
V
F
All temperatures
All temperatures
All temperatures
All temperatures
OSC
OSC
OSC
OSC
OSC
OSC
OSC
DD
DD
DD
DD
DD
DD
DD
DD
DD
= 3.0V, Commercial, WDT disabled
= 3.0V, Industrial, WDT disabled
= 3.0V, Extended, WDT disabled
= 5.5V, Commercial, WDT disabled
= 5.5V, Industrial, WDT disabled
= 5.5V, Extended, WDT disabled
= 3.0V, Commercial
= 3.0V, Industrial
= 3.0V, Extended
= 4MHz, V
= 4MHz, V
= 10MHz, V
= 32kHz, V
= 32kHz, V
= 32kHz, V
= 4MHz, V
T
T
A
A
PIC16C433
SS
+85°C
+125°C for extended
, T0CKI = V
DD
DD
DD
Conditions
DD
DD
DD
DD
DD
= 3.0V
= 3.0V
= 5.5V, SCL = 400kHz
= 3.0V, WDT disabled
= 3.0V, WDT disabled
= 3.0V, WDT disabled
= 5.5V
for industrial
or V
DS41139A-page 87
DD
SS
,
.