PIC18F24K20-E/SS Microchip Technology, PIC18F24K20-E/SS Datasheet - Page 4
![IC PIC MCU FLASH 8KX16 28-SSOP](/photos/6/81/68119/150-28-ssop_sml.jpg)
PIC18F24K20-E/SS
Manufacturer Part Number
PIC18F24K20-E/SS
Description
IC PIC MCU FLASH 8KX16 28-SSOP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC18F25K20T-ISS.pdf
(42 pages)
2.PIC18F25K20T-ISS.pdf
(12 pages)
3.PIC18F25K20T-ISS.pdf
(14 pages)
4.PIC18F25K20T-ISS.pdf
(456 pages)
Specifications of PIC18F24K20-E/SS
Core Size
8-Bit
Program Memory Size
16KB (8K x 16)
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
24
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SSOP
Controller Family/series
PIC18
No. Of I/o's
25
Eeprom Memory Size
256Byte
Ram Memory Size
768Byte
Cpu Speed
64MHz
No. Of Timers
4
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PIC18F24K20/25K20/44K20/45K20
Silicon Errata Issues
1. Module: ECCP
2. Module: ECCP
3. Module: MSSP SPI
DS80425G-page 4
Note 1: This document summarizes all silicon
Changing the CCP1M<3:0> bits of CCP1CON
may cause the CCPR1H and CCPR1L registers to
capture the value of Timer1.
Work around
Halt Timer1 before changing ECCP mode. Reload
Timer1 with desired value after ECCP is setup and
before Timer1 is restarted.
Affected Silicon Revisions
Changing direction in Full-Bridge mode does not
insert dead time between changing the active
drivers in common legs of the bridge.
Work around
None.
Affected Silicon Revisions
When the SPI clock is configured for Timer2/2
(SSPCON1<3:0> = 0011), the first SPI high time
may be short.
Work around
Option 1: Ensure TMR2 value rolls over to zero
Option 2: Turn Timer2 off and clear TMR2 before
Affected Silicon Revisions
X
X
X
2: Shaded cells in this section indicate latest
errata issues from all specified revisions
of silicon.
silicon in production.
X
X
X
writing SSPBUF. Enable TMR2 after
SSPBUF is written.
immediately before writing to SSPBUF.
X
X
X
X
X
X
4. Module: MSSP I
5. Module: ADC
6. Module: MSSP I
Slew rate is slower than I
the SLRCON<2> bit is set.
Work around
Clear SLRCON<2> bit when using the I
peripheral.
Affected Silicon Revisions
Offset error is 3 LSb typical, 7 LSb maximum,
including
component (~2 LSb).
Work around
The time dependent error is insignificant when the
time between conversions is less than 100 ms.
When the time since the previous conversion is
greater than 100 ms then take two ADC
conversions and discard the first.
Affected Silicon Revisions
If a new address byte is received while the BF flag
is set, the SSPOV bit is properly set and an ACK is
not properly generated. If only the SSPOV bit is set
(BF flag was cleared) and a matching address is
clocked in, that received byte will be improperly
loaded into the SSPBUF register and an ACK will
be improperly generated.
Work around
None.
Affected Silicon Revisions
X
X
X
X
X
X
an
X
X
X
2010 Microchip Technology Inc.
acquisition
2
2
X
X
X
C™
C
2
C specifications when
time-dependent
2
C