AT90PWM316-16MU Atmel, AT90PWM316-16MU Datasheet - Page 289

• Manufacturer Part Number: AT90PWM316-16MU
• Description: MCU AVR 16K FLASH 16MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM316-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-QFN
• Processor Series: AT90PWMx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 2
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRFBKIT, ATAVRISP2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Cpu Family: 90P
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 1KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: QFN EP
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOICATAVRMC200 - KIT EVAL FOR AT90PWM3 ASYNCATAVRFBKIT - KIT DEMO BALLAST FOR AT90PWM2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7710E–AVR–08/10
I. Repeat B through H until the entire Flash is programmed or until all data has been
programmed.
J. End Page Programming
Figure 25-2. Addressing the Flash Which is Organized in Pages
Note:
Figure 25-3. Programming the Flash Waveforms
Note:
1. Give WR a negative pulse. This starts programming of the entire page of data.
2. Wait until RDY/BSY goes high (See
1. 1. Set XA1, XA0 to “10”. This enables command loading.
2. Set DATA to “0000 0000”. This is the command for No Operation.
3. Give XTAL1 a positive pulse. This loads the command, and the internal write signals
RESET +12V
RDY/BSY goes low.
are reset.
RDY/BSY
PAGEL
1. PCPAGE and PCWORD are listed in
XTAL1
1. “XX” is don’t care. The letters refer to the programming description above.
DATA
XA1
XA0
BS1
BS2
WR
OE
PROGRAM MEMORY
PROGRAM
COUNTER
0x10
PAGE
A
PAGE ADDRESS
WITHIN THE FLASH
ADDR. LOW
B
PCMSB
DATA LOW
C
PCPAGE
DATA HIGH
D
XX
E
Figure 25-3
PAGEMSB
ADDR. LOW
PCWORD
B
Table 25-11 on page
WORD ADDRESS
WITHIN A PAGE
DATA LOW
(1)
C
F
for signal waveforms).
DATA HIGH
INSTRUCTION WORD
D
PAGE
AT90PWM216/316
XX
E
286.
(1)
ADDR. HIGH
G
H
PCWORD[PAGEMSB:0]:
XX
00
01
02
PAGEEND
289