PIC16F676T-E/ST Microchip Technology, PIC16F676T-E/ST Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC16F676T-E/ST
Manufacturer Part Number
PIC16F676T-E/ST
Description
IC MCU FLASH 1KX14 W/AD 14TSSOP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC12F629T-ISN.pdf
(24 pages)
3.PIC16F630-ISL.pdf
(132 pages)
4.PIC16F630-ISL.pdf
(2 pages)
5.PIC16F630-ISL.pdf
(10 pages)
Specifications of PIC16F676T-E/ST
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
12
Program Memory Size
1.75KB (1K x 14)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
14-TSSOP
For Use With
XLT14SS-1 - SOCKET TRANSITION 14DIP/14SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
4.4
An 8-bit counter is available as a prescaler for the
Timer0 module, or as a postscaler for the Watchdog
Timer. For simplicity, this counter will be referred to as
“prescaler” throughout this Data Sheet. The prescaler
assignment is controlled in software by the control bit
PSA (OPTION_REG<3>). Clearing the PSA bit will
assign the prescaler to Timer0. Prescale values are
selectable via the PS2:PS0 bits (OPTION_REG<2:0>).
The prescaler is not readable or writable. When
assigned to the Timer0 module, all instructions writing
to the TMR0 register (e.g., CLRF 1,
BSF 1, x....etc.) will clear the prescaler. When
assigned to WDT, a CLRWDT instruction will clear the
prescaler along with the Watchdog Timer.
4.4.1
The prescaler assignment is fully under software
control (i.e., it can be changed “on the fly” during
program execution). To avoid an unintended device
Reset, the following instruction sequence (Example 4-
1) must be executed when changing the prescaler
assignment from Timer0 to WDT.
TABLE 4-1:
2010 Microchip Technology Inc.
01h
0Bh/8Bh
81h
85h
Legend:
Address
Prescaler
TMR0
INTCON
OPTION_REG
TRISA
Shaded cells are not used by the Timer0 module.
– = Unimplemented locations, read as ‘0’, u = unchanged, x = unknown.
SWITCHING PRESCALER
ASSIGNMENT
Name
REGISTERS ASSOCIATED WITH TIMER0
Timer0 Module Register
RAPU
Bit 7
GIE
—
INTEDG
PEIE
Bit 6
—
TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 --11 1111 --11 1111
MOVWF 1,
T0CS
Bit 5
T0IE
T0SE
INTE
Bit 4
RAIE
Bit 3
PSA
EXAMPLE 4-1:
To change prescaler from the WDT to the TMR0
module, use the sequence shown in Example 4-2. This
precaution must be taken even if the WDT is disabled.
EXAMPLE 4-2:
BCF
CLRWDT
CLRF
BSF
MOVLW
MOVWF
CLRWDT
MOVLW
MOVWF
BCF
CLRWDT
BSF
MOVLW
MOVWF
BCF
Bit 2
T0IF
PS2
STATUS,RP0
TMR0
STATUS,RP0
b’00101111’ ;Required if desired
OPTION_REG
b’00101xxx’ ;Set postscaler to
OPTION_REG
STATUS,RP0
STATUS,RP0
b’xxxx0xxx’ ;Select TMR0,
OPTION_REG
STATUS,RP0
PIC16F630/676
Bit 1
INTF
PS1
CHANGING PRESCALER
(TIMER0WDT)
CHANGING PRESCALER
(WDTTIMER0)
RAIF
Bit 0
PS0
;Bank 0
;Clear WDT
;Clear TMR0 and
; prescaler
;Bank 1
; PS2:PS0 is
; 000 or 001
;
; desired WDT rate
;Bank 0
;Clear WDT and
; postscaler
;Bank 1
; prescale, and
; clock source
;
;Bank 0
xxxx xxxx uuuu uuuu
0000 0000 0000 000u
1111 1111 1111 1111
POR, BOD
Value on
DS40039F-page 33
Value on
all other
Resets