PIC16F1826-E/P Microchip Technology, PIC16F1826-E/P Datasheet - Page 8

• Manufacturer Part Number: PIC16F1826-E/P
• Description: MCU PIC 8BIT 2K FLASH 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1826-E/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 32MHz
• No. Of Timers: 3
• Core: PIC
• Processor Series: PIC16F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 32 MHz
• Data Ram Size: 256 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 15
• Number Of Timers: 3
• Mounting Style: Through Hole
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 3.3 mm
• Interface Type: I2C, SPI, UART
• Length: 22.86 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.3 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F/LF182X/PIC12F/LF1822
3.1
A user may store identification information (user ID) in
four designated locations. The user ID locations are
mapped to 8000h-8003h. Each location is 14 bits in
length. Code protection has no effect on these memory
locations. Each location may be read with code
protection enabled or disabled.
REGISTER 3-1:
DS41390C-page 8
bit 13
bit 6
Legend:
R = Readable bit
-n = Value at POR
bit 13-5
bit 4-0
Note 1:
Note:
DEV8
DEV1
R
R
User ID Location
This location cannot be written.
MPLAB
Significant bits (LSb) of each user ID
location, the upper bits are not read. It is
recommended that only the 7 LSb’s be
used if MPLAB IDE is the primary tool
used to read these addresses.
DEV<8:0>: Device ID bits
These bits are used to identify the part number.
REV<4:0>: Revision ID bits
These bits are used to identify the revision.
®
IDE only displays the 7 Least
DEVICE ID: DEVICE ID REGISTER
DEV7
DEV0
R
R
P = Programmable bit
W = Writable bit
‘1’ = Bit is set
DEV6
REV4
R
R
Advance Information
DEV5
REV3
R
R
(1)
3.2
The device ID word is located at 8006h. This location is
read-only and cannot be erased or modified.
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Device ID
DEV4
REV2
R
R
 2010 Microchip Technology Inc.
DEV3
REV1
R
R
DEV2
REV0
R
R
bit 7
bit 0