PIC16F1826-E/P Microchip Technology, PIC16F1826-E/P Datasheet - Page 8

• Manufacturer Part Number: PIC16F1826-E/P
• Description: MCU PIC 8BIT 2K FLASH 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1826-E/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 32MHz
• No. Of Timers: 3
• Core: PIC
• Processor Series: PIC16F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 32 MHz
• Data Ram Size: 256 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 15
• Number Of Timers: 3
• Mounting Style: Through Hole
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 3.3 mm
• Interface Type: I2C, SPI, UART
• Length: 22.86 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.3 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16(L)F1826/1827
9. Module: BOR
9.1 BOR Reset
DS80485G-page 8
This issue affects only the PIC16LF1826/1827
devices. The device may undergo a BOR Reset
when waking-up from Sleep and BOR is re-
enabled. A BOR Reset may also occur the
moment the software BOR is enabled.
Under certain voltage and temperature conditions
and when either SBODEN or BOR_NSLEEP is
selected, the devices may occasionally reset when
waking-up from Sleep or BOR is enabled.
Work around
Method 1: In applications where BOR use is
Method 2: Set the FVREN bit of the
Method 3: When BOR module is needed
Method 4: Use the software-enabled BOR
not critical, turn off the BOR in the
Configuration Word.
FVRCON register. Maintain this
bit on at all times.
only during run-time, use the
software-enabled BOR by setting
the SBODEN option on the
Configuration Word. BOR should
be turned off by software before
Sleep, then follow the below
sequence for turning BOR on
after Wake-up:
as described in Method 3, but use
the following sequence:
a. Switch to internal 32 kHz
b. Upon wake-up, turn on FVR
c. Manually turn on the BOR;
d. Switch the clock back to the
a. Wake-up event occurs;
b. Turn on FVR (FVREN bit of the
c. Wait until FVRRDY bit is set;
d. Wait 15 µs after the FVR
e. Manually turn on the BOR.
FVRCON register);
Ready bit is set;
oscillator immediately before
Sleep;
(FVREN bit of the FVRCON
register);
preferred clock source.
Note:
Affected Silicon Revisions
A2
X
When using the software BOR follow the
steps in Methods 3 or 4 above when
enabling BOR for the first time during
program execution.
A3
X
A4
X
 2011 Microchip Technology Inc.