ATTINY13-20SSQ Atmel, ATTINY13-20SSQ Datasheet - Page 88
![MCU AVR 1KB FLASH 20MHZ 8SOIC GW](/photos/6/50/65032/453-8-soic_sml.jpg)
ATTINY13-20SSQ
Manufacturer Part Number
ATTINY13-20SSQ
Description
MCU AVR 1KB FLASH 20MHZ 8SOIC GW
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY13-20SSQ
Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1KB (512 x 16)
Program Memory Type
FLASH
Eeprom Size
64 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Processor Series
ATTINY1x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
64 B
Interface Type
SPI
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
6
Number Of Timers
1
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAKSTK511
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 4 Channel
For Use With
ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVR
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
Lead Free Status / Rohs Status
Details
- Current page: 88 of 176
- Download datasheet (3Mb)
14.9
14.10 ADC Accuracy Definitions
88
Analog Noise Canceling Techniques
ATtiny13
The ADC is optimized for analog signals with an output impedance of approximately 10 kΩ or
less. If such a source is used, the sampling time will be negligible. If a source with higher imped-
ance is used, the sampling time will depend on how long time the source needs to charge the
S/H capacitor, with can vary widely. The user is recommended to only use low impedant sources
with slowly varying signals, since this minimizes the required charge transfer to the S/H
capacitor.
Signal components higher than the Nyquist frequency (f
distortion from unpredictable signal convolution. The user is advised to remove high frequency
components with a low-pass filter before applying the signals as inputs to the ADC.
Digital circuitry inside and outside the device generates EMI which might affect the accuracy of
analog measurements. When conversion accuracy is critical, the noise level can be reduced by
applying the following techniques:
Where high ADC accuracy is required it is recommended to use ADC Noise Reduction Mode, as
described in
is above 1 MHz. A good system design with properly placed, external bypass capacitors does
reduce the need for using ADC Noise Reduction Mode
An n-bit single-ended ADC converts a voltage linearly between GND and V
(LSBs). The lowest code is read as 0, and the highest code is read as 2
Several parameters describe the deviation from the ideal behavior:
• Keep analog signal paths as short as possible.
• Make sure analog tracks run over the analog ground plane.
• Keep analog tracks well away from high-speed switching digital tracks.
• If any port pin is used as a digital output, it mustn’t switch while a conversion is in progress.
• Place bypass capacitors as close to V
Section 14.7 on page
87. This is especially the case when system clock frequency
CC
and GND pins as possible.
ADC
/2) should not be present to avoid
n
-1.
REF
2535J–AVR–08/10
in 2
n
steps
Related parts for ATTINY13-20SSQ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATTINY13-20SI](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATtiny13](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATTINY13-20SSU](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20MU](/photos/6/87/68751/313-20-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 10MHZ 20-MLF
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20PU](/photos/6/50/65033/313-8-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 20MHZ 8DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20MMU](/photos/12/13/121304/313-10m1_tmb.jpg)
Part Number:
Description:
MCU AVR 1KB FLASH 20MHZ 3X3 QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20SU](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20PJ](/photos/6/50/65033/313-8-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K 5V 20MHZ 8DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20SJ](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K 5V 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20SSJ](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K 5V 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20PI](/photos/6/50/65033/313-8-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 20MHZ 8DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY13-20SSI](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 1K FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet: