PIC12F615-I/P Microchip Technology, PIC12F615-I/P Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12F615-I/P
Manufacturer Part Number
PIC12F615-I/P
Description
IC PIC MCU FLASH 1KX14 8DIP
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Datasheets
1.PIC12F609T-ISN.pdf
(212 pages)
2.PIC12F609T-ISN.pdf
(26 pages)
3.PIC12F609T-ISN.pdf
(8 pages)
4.PIC12F615-ESN.pdf
(168 pages)
Specifications of PIC12F615-I/P
Program Memory Type
FLASH
Program Memory Size
1.75KB (1K x 14)
Package / Case
8-DIP (0.300", 7.62mm)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
5
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC12F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
64 B
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
5
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
Minimum Operating Temperature
- 40 C
On-chip Adc
4-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
APGRD004 - REF DESIGN MOD AUTO AMBNT LIGHTAC162083 - HEADER MPLAB ICD2 PIC16F616 8/14ACICE0201 - MPLABICE 8P 300 MIL ADAPTERAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC12F615-I/P
Manufacturer:
MICROCHI
Quantity:
1 000
Part Number:
PIC12F615-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC12F609/615/12HV609/615
3.2
Clock Source modes can be classified as external or
internal.
• External Clock modes rely on external circuitry for
• Internal clock sources are contained internally
The system clock can be selected between external or
internal clock sources via the FOSC<2:0> bits of the
Configuration Word register.
TABLE 3-1:
3.3.2
The External Clock (EC) mode allows an externally
generated logic level as the system clock source. When
operating in this mode, an external clock source is
connected to the OSC1 input and the OSC2 is available
for general purpose I/O. Figure 3-2 shows the pin
connections for EC mode.
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 3-2:
DS41302A-page 26
Switch From
Sleep/POR
Sleep/POR
Sleep/POR
Note 1:
the clock source. Examples are: Oscillator mod-
ules (EC mode), quartz crystal resonators or
ceramic resonators (LP, XT and HS modes) and
Resistor-Capacitor (RC) mode circuits.
within the Oscillator module. The Oscillator
module has two selectable clock frequencies:
4 MHz and 8 MHz
Clock from
Ext. System
Clock Source Modes
EC MODE
Alternate pin functions are listed in the
Section 1.0 “Device Overview”.
I/O
OSCILLATOR DELAY EXAMPLES
EXTERNAL CLOCK (EC)
MODE OPERATION
OSC1/CLKIN
OSC2/CLKOUT
Switch To
INTOSC
EC, RC
LP, XT, HS
®
PIC
MCU design is fully
®
MCU
(1)
Preliminary
DC – 20 MHz
Frequency
125 kHz to 8 MHz
32 kHz to 20 MHz
3.3
3.3.1
If the Oscillator module is configured for LP, XT or HS
modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the Oscillator
module. When switching between clock sources, a
delay is required to allow the new clock to stabilize.
These oscillator delays are shown in Table 3-1.
External Clock Modes
OSCILLATOR START-UP TIMER (OST)
Oscillator Delay
Oscillator Warm-Up Delay (T
2 instruction cycles
1024 Clock Cycles (OST)
© 2006 Microchip Technology Inc.
WARM
)