PIC16HV616-I/ST Microchip Technology, PIC16HV616-I/ST Datasheet - Page 3

• Manufacturer Part Number: PIC16HV616-I/ST
• Description: IC PIC MCU FLASH 2KX14 14TSSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16HV616-I/ST

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 11
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-TSSOP
• Controller Family/series: PIC16HV
• No. Of I/o's: 12
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Processor Series: PIC16H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 11
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162083 - HEADER MPLAB ICD2 PIC16F616 8/14AC164306 - MODULE SKT FOR PM3 20TSSOP
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

3.0
3.1
The user memory space extends from 0x0000 to
0x1FFF. In Program/Verify mode, the program memory
space extends from 0x0000 to 0x3FFF, with the first
half (0x0000-0x1FFF) being user program memory and
the second half (0x2000-0x3FFF) being configuration
memory. The PC will increment from 0x0000 to 0x1FFF
and wrap to 0x0000. If the PC is between 0x2000 to
0x3FFF it will wrap around to 0x2000 (not to 0x0000).
Once in configuration memory, the highest bit of the PC
stays a ‘1’, thus always pointing to the configuration
memory. The only way to point to user program
memory is to reset the part and re-enter Program/Verify
mode as described in Section 4.0 “Program/Verify
Mode”.
For
PIC12HV609/12HV615/16HV610/16HV616 devices,
the configuration memory space, 0x2000 to 0x2008,
are physically implemented. However, only locations
0x2000 to 0x2003, 0x2007 and 0x2008 are available.
Other locations are reserved.
3.2
A user may store identification information (user ID) in
four designated locations. The user ID locations are
mapped in 0x2000 to 0x2003. It is recommended that
the user use only the seven Least Significant bits (LSb)
of each user ID location. The user ID locations read out
normally, even after code protection is enabled. It is
recommended that ID locations are written as ‘xx
xxxx xbbb bbbb’ where ‘bbb
information.
The 14 bits may be programmed, but only the 7 LSb’s
are displayed by MPLAB
care” bits and are not read by MPLAB
 2009 Microchip Technology Inc.
PIC12F609/12F615/16F610/16F616/PIC12HV609/12HV615/16HV610/16HV616
the
MEMORY DESCRIPTION
Program Memory Map
User ID Locations
PIC12F609/12F615/16F610/16F616/
®
IDE. The xxxx’s are “don’t
bbbb’ is user ID
®
IDE.
3.3
For
PIC12HV609/12HV615/16HV610/16HV616 devices,
the 4/8 MHz Internal Oscillator (INTOSC) module is
factory calibrated. This value is stored in the
device data sheet for more information.
The Calibration Word locations are written at the time
of manufacturing and are not erased when a Bulk
Erase is performed. See Section 4.1.4.7 “Bulk Erase
Program Memory” for more information on the various
erase sequences. However, it is possible to inadver-
tently write to these locations. The device may not func-
tion properly or may operate outside of specifications if
the Calibration Word locations do not contain the cor-
rect value. Therefore, it is recommended that the Cali-
bration Words be read prior to any programming
procedure and verified after programming is complete.
See Figure 4-15 for a flowchart of the recommended
verification procedure.
The device should not be used if the verification of the
Calibration Word values fail after the device is
programmed. The 0x3FFF value is a special case, it is
a valid calibration value but, it is also the erased state
of the register.
Calibration Word (0x2008). See the applicable
the
Calibration Word
PIC12F609/12F615/16F610/16F616/
DS41284D-page 3