M3087BFLBGP#U5 Renesas Electronics America, M3087BFLBGP#U5 Datasheet - Page 388

• Manufacturer Part Number: M3087BFLBGP#U5
• Description: IC M32C/87 MCU FLASH 144LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M3087BFLBGP#U5

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IEBus, IrDA, SIO, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 121
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 34x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 144-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M32C/87 Group (M32C/87, M32C/87A, M32C/87B)
REJ09B0180-0151 Rev.1.51 Jul 31, 2008
Page 364 of 587
22.3.6
Table 22.13
NOTE:
Waveform generation channels
OUTC2_i pin
Waveform output start condition
Waveform output stop condition
Interrupt request generation timing An interrupt request is generated at the second clock cycle after the base timer
Selectable function
1. Channels 0 to 7 are provided in the 144-pin package. Channels 0 to 2 are provided in the 100-pin package.
In parallel real-time port output mode, all of the channels which the RTP bit in the G2POCRi register (i = 0 to 7)
is set to 1, perform the parallel real-time port output. The value set in the G2RTP register is output from the
OUTC2_i pin in these channels, when the base timer value matches any of the G2POi register which the RTP
bit is set to 1. Real-time port output and parallel real-time port output cannot be used in the same group. To use
parallel real-time port output, set the RTP bit to 1 and the PRT bit to 1 in the channel used for parallel real-time
port output. Also, set the PRP bit in the G2BCR1 register to 1.
Table 22.13 lists specifications of parallel real-time port output mode. Figure 22.33 shows a block diagram.
Figure 22.34 shows an example of parallel real-time port output mode operation.
Parallel Real-Time Port Output Mode (Group 2)
Item
Specifications of parallel real-time port output mode
Group 2: channels 0 to 7
Real-time port output
Set both the BTS bit in the G2BCR1 register and the IFEi bit in the G2FE register
to 1
Set either the BTS or IFEi bit to 0
value matches the G2POi register value.
• Initial value set function:
The PO2iR bit in the IIOkIR register (k = 3, 5 to 11) becomes 1 (interrupt
requested) when an interrupt request is generated.
(See Figure 11.18 IIO0IR to IIO11IR Registers)
Set the initial output level when waveform output is started (determined by the
IVL bit in the G2POCRi register)
(1)
22. Intelligent I/O (Waveform Generation Function)
Specification