EP9315-CB Cirrus Logic Inc, EP9315-CB Datasheet - Page 11

• Manufacturer Part Number: EP9315-CB
• Description: IC ARM920T MCU 200MHZ 352-PBGA
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9315-CB

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, PCMCIA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 352-BGA
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9315A-Z
• For Use With: 598-1144 - KIT DEVELOPMENT EP9315 ARM9
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No
• Other names: 598-1261

Reset and Power Management
The chip may be reset through the PRSTn pin or through
the open drain common reset pin, RSTOn.
Clocks are managed on a peripheral-by-peripheral basis
and may be turned off to conserve power.
The processor clock is dynamically adjustable from 0 to
200 MHz (184 MHz for industrial conditions).
Hardware Debug Interface
The JTAG interface allows use of ARM’s Multi-ICE or
other in-circuit emulators.
Internal Boot ROM
The Internal 16-kbyte ROM allows booting from FLASH
memory, SPI or UART. Consult the EP93xx User’s
Manual for operational details
DS638PP4
PRSTn
RSTOn
EGPIO[15:0]
FGPIO[7:0]
TCK
TDI
TDO
TMS
TRSTn
Pin Mnemonic
Note:
Note:
Pin Mnemonic
Pin Mnemonic
Table Q. Reset and Power Management Pin Assignments
Table P. General Purpose Input/Output Pin Assignment
Port F defaults as PCMCIA pins. Port F must be
configured by software to be used as GPIO.
The JTAG interface does not support boundary scan.
Table R. Hardware Debug Interface
Expanded General Purpose Input / Output
Pins with Interrupts
Expanded General Purpose Input / Output
Pins with Interrupts
Power On Reset
User Reset In/Out – Open Drain –
Preserves Real Time Clock value
JTAG Clock
JTAG Data In
JTAG Data Out
JTAG Test Mode Select
JTAG Port Reset
Pin Name - Description
Pin Name - Description
Pin Name - Description
©
Copyright 2005 Cirrus Logic (All Rights Reserved)
12-channel DMA Controller
The DMA module contains 12 separate DMA channels.
Ten of these may be used for peripheral-to-memory or
memory-to-peripheral
dedicated to memory-to-memory transfers. Each DMA
channel is connected to the 16-bit DMA request bus.
The request bus is a collection of requests, Serial Audio,
and UARTs. Each DMA channel can be used
independently or dedicated to any request signal. For
each DMA channel, source and destination addressing
can be independently programmed to increment,
decrement, or stay at the same value. All DMA
addresses are physical, not virtual addresses.
PCMCIA Interface
The EP9315 has a single PCMCIA port which can be
used to access either 8 or 16-bit devices.
VS1
VS2
MCD1
MCD2
MCBVD1
MCBVD2
MCDIR
MCDAENn
MCADENn
MCREGn
MCEHn
MCELn
IORDn
IOWRn
MCRDn
MCWRn
READY
WP
MCWAITn
MCRESETn
Pin Mnemonic
Enhanced Universal Platform SOC Processor
Table S. PCMCIA Interface
Voltage sense
Voltage sense
Card detect
Card detect
Voltage detection / status change
Voltage detection
Data transceiver direction control
Data bus transceiver enable
Address bus transceiver enable
Memory card register
Memory card high byte select
Memory card low byte select
I/O card read
I/O card write
Memory card read
Memory card write
Ready / interrupt
Write protect
Wait Input
Card reset
access.
Pin Name - Description
Two
of
these
EP9315
are
11