PIC16F526-I/P Microchip Technology, PIC16F526-I/P Datasheet - Page 41

• Manufacturer Part Number: PIC16F526-I/P
• Description: IC PIC MCU FLASH 1KX12 14DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F526-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.5KB (1K x 12)
• Package / Case: 14-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 11
• Ram Size: 67 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 3x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 67 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 3 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162096 - HEADER MPLAB ICD2 PIC16F526 8/14
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.2
8.2.1
The PIC16F526 device can be operated in up to six dif-
ferent Oscillator modes. The user can program up to
three Configuration bits (FOSC<2:0>). To select one of
these modes:
• LP:
• XT:
• HS:
• INTRC: Internal 4/8 MHz Oscillator
• EXTRC: External Resistor/Capacitor
• EC:
8.2.2
In HS, XT or LP modes, a crystal or ceramic resonator
is
RB4/OSC2/CLKOUT pins to establish oscillation
(Figure 8-1). The PIC16F526 oscillator designs require
the use of a parallel cut crystal. Use of a series cut crys-
tal may give a frequency out of the crystal manufactur-
ers specifications. When in HS, XT or LP modes, the
device can have an external clock source drive the
RB5/OSC1/CLKIN pin (Figure 8-2). This pin should be
left open and unloaded. Also when using this mode, the
external clock should observe the frequency limits for
the Clock mode chosen (HS, XT or LP).
© 2007 Microchip Technology Inc.
Note 1: This device has been designed to per-
connected
2: The user should verify that the device
Oscillator Configurations
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
External High-Speed Clock Input
CRYSTAL OSCILLATOR/CERAMIC
RESONATORS
OSCILLATOR TYPES
form to the parameters of its data sheet.
It has been tested to an electrical
specification designed to determine its
conformance with these parameters.
Due to process differences in the
manufacture of this device, this device
may have different performance charac-
teristics than its earlier version. These
differences may cause this device to
perform differently in your application
than the earlier version of this device.
oscillator
expected. Adjusting the loading capacitor
values and/or the Oscillator mode may
be required.
to
the
starts
RB5/OSC1/CLKIN
and
performs
and
Preliminary
as
FIGURE 8-1:
FIGURE 8-2:
TABLE 8-1:
Note 1:
OSC2/CLKOUT/RB4
EC, HS, XT, LP
Note 1:
Note 1: RB4 is available in EC mode only.
Type
Osc
Clock From
ext. system
XT
HS
C2
C1
2:
3:
(1)
(1)
Resonator
These values are for design guidance
only. Since each resonator has its own
characteristics, the user should consult
the resonator manufacturer for
appropriate values of external
components.
4.0 MHz
See Capacitor Selection tables for
recommended values of C1 and C2.
A series resistor (RS) may be required for AT
strip cut crystals.
RF approx. value = 10 MΩ.
16 MHz
Freq.
RS
XTAL
(2)
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
CRYSTAL OPERATION
(OR CERAMIC
RESONATOR)
(HS, XT OR LP OSC
CONFIGURATION)
EXTERNAL CLOCK INPUT
OPERATION (HS, XT, LP
OR EC OSC
CONFIGURATION)
Cap. Range
PIC16F526
10-47 pF
OSC2/CLKOUT/RB4
RB5/OSC1/CLKIN
30 pF
C1
RF
(3)
PIC16F526
DS41326A-page 39
PIC16F526
Cap. Range
10-47 pF
To internal
Sleep
30 pF
C2
logic
(1)