MC9S08LL16CGT Freescale Semiconductor, MC9S08LL16CGT Datasheet - Page 10
![IC MCU 8BIT 16K FLASH 48-QFN](/photos/37/62/376240/qfn-48_sml.jpg)
MC9S08LL16CGT
Manufacturer Part Number
MC9S08LL16CGT
Description
IC MCU 8BIT 16K FLASH 48-QFN
Manufacturer
Freescale Semiconductor
Series
HCS08r
Datasheet
1.DEMO9S08LL16.pdf
(44 pages)
Specifications of MC9S08LL16CGT
Core Processor
HCS08
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SCI, SPI
Peripherals
LCD, LVD, POR, PWM, WDT
Number Of I /o
31
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 8x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-QFN
Processor Series
S08LL
Core
HCS08
Data Bus Width
8 bit
Data Ram Size
2080 B
Interface Type
I2C/SCI/SPI
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
31
Number Of Timers
1
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWS08
Development Tools By Supplier
TWR-SER, TWR-ELEV, TWR-S08LL64, TWR-SENSOR-PAK, TWR-S08LL64-KIT, TWR-LCD
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 12-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Electrical Characteristics
3.3
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not
guaranteed. Stress beyond the limits specified in
damage to the device. For functional operating conditions, refer to the remaining tables in this section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (for instance, either V
pull-up resistor associated with the pin is enabled.
10
C
D
P
T
Absolute Maximum Ratings
1
2
3
Those parameters are guaranteed during production testing on each individual device.
Those parameters are achieved by the design characterization by measuring a statistically relevant
sample size across process variations.
Those parameters are achieved by design characterization on a small sample size from typical devices
under typical conditions unless otherwise noted. All values shown in the typical column are within this
category.
Those parameters are derived mainly from simulations.
Supply voltage
Maximum current into V
Digital input voltage
Instantaneous maximum current
Storage temperature range
current-limiting resistor, calculate resistance values for positive (V
voltages, then use the larger of the two resistance values.
All functional non-supply pins, except for PTB2 are internally clamped to V
Power supply must maintain regulation within operating V
operating maximum current conditions. If positive injection current (V
I
out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
The classification is shown in the column labeled “C” in the parameter
tables where appropriate.
Input must be current limited to the value specified. To determine the value of the required
DD
Single pin limit (applies to all port pins)
, the injection current may flow out of V
Rating
MC9S08LL16 Series MCU Data Sheet, Rev. 6
DD
Table 4. Absolute Maximum Ratings
Table 3. Parameter Classifications
DD
load will shunt current greater than maximum injection
1, 2, 3
Table 4
NOTE
DD
and could result in external power supply going
may affect device reliability or cause permanent
Symbol
V
T
I
V
DD
I
DD
stg
D
In
DD
range during instantaneous and
DD
–0.3 to V
) and negative (V
In
–0.3 to 3.8
–55 to 150
SS
> V
Value
25
120
or V
SS
DD
DD
) is greater than
and V
+ 0.3
DD
) or the programmable
DD
Freescale Semiconductor
SS
.
) clamp
Unit
mA
mA
C
V
V