C8051F314-GQ Silicon Laboratories Inc, C8051F314-GQ Datasheet - Page 107
![IC 8051 MCU 8K FLASH 32LQFP](/photos/12/16/121617/c8051f314-gq_sml.jpg)
C8051F314-GQ
Manufacturer Part Number
C8051F314-GQ
Description
IC 8051 MCU 8K FLASH 32LQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F31xr
Specifications of C8051F314-GQ
Program Memory Type
FLASH
Program Memory Size
8KB (8K x 8)
Package / Case
32-LQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
29
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F3x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
29
Number Of Timers
4
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F310DK
Minimum Operating Temperature
- 40 C
On-chip Adc
17-chx10-bit
No. Of I/o's
29
Ram Memory Size
1280Byte
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1445 - ADAPTER PROGRAM TOOLSTICK F310
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1257
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F314-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F314-GQR
Manufacturer:
ST
Quantity:
15 000
Company:
Part Number:
C8051F314-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
any other reset source. For example, if the V
V
Important Note: The V
V
dure for configuring the V
See Figure 9.2 for V
See Table 9.1 for complete electrical characteristics of the V
9.3.
The external RST pin provides a means for external circuitry to force the device into a reset state. Assert-
ing an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST
pin may be necessary to avoid erroneous noise-induced resets. See Table 9.1 for complete RST pin spec-
ifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
DD
DD
Bit7:
Bit6:
Bits5–0: Reserved. Read = Variable. Write = don’t care.
VDMEN VDDSTAT Reserved Reserved Reserved Reserved Reserved Reserved
monitor will still be enabled after the reset.
monitor as a reset source before it is enabled and stabilized may cause a system reset. The proce-
R/W
Bit7
Step 1. Enable the V
Step 2. Wait for the V
Step 3. Select the V
External Reset
VDMEN: V
This bit is turns the V
resets until it is also selected as a reset source in register RSTSRC (Figure 9.2). The V
Monitor must be allowed to stabilize before it is selected as a reset source. Selecting the
V
See Table 9.1 for the minimum V
0: V
1: V
V
This bit indicates the current power supply status (V
0: V
1: V
DD
DD
DD
DD
DD
DD
Note: This delay should be omitted if software contains routines that erase or write Flash
memory.
monitor as a reset source before it has stabilized may generate a system reset.
STAT: V
Bit6
R
Monitor Disabled.
Monitor Enabled.
is at or below the V
is above the V
DD
SFR Definition 9.1. VDM0CN: V
DD
DD
monitor timing; note that the reset delay is not incurred after a V
DD
DD
Monitor Enable.
monitor must be enabled before it is selected as a reset source. Selecting the
Status.
monitor as a reset source is shown below:
DD
Bit5
DD
R
DD
monitor as a reset source (PORSF bit in RSTSRC = ‘1’).
monitor (VDMEN bit in VDM0CN = ‘1’).
monitor to stabilize (see Table 9.1 for the V
DD
DD
monitor circuit on/off. The V
monitor threshold.
DD
Bit4
R
monitor threshold.
DD
DD
monitor is enabled and a software reset is performed, the
Monitor turn-on time.
Rev. 1.7
Bit3
R
C8051F310/1/2/3/4/5/6/7
DD
DD
Bit2
monitor.
R
DD
DD
Monitor Control
Monitor output).
Monitor cannot generate system
Bit1
R
DD
Monitor turn-on time).
SFR Address:
Bit0
R
DD
monitor reset.
0xFF
Reset Value
Variable
DD
107