PIC18LF8720-I/PT Microchip Technology, PIC18LF8720-I/PT Datasheet - Page 18

• Manufacturer Part Number: PIC18LF8720-I/PT
• Description: IC MCU FLASH 64KX16 LV 80-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF8720-I/PT

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.75K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 68
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.75KB
• Cpu Speed: 25MHz
• No. Of Timers: 5
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3840 B
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 68
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM183032, DM183022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18FXX20
3.4
The ID Locations are programmed much like the code
memory, except that multi-panel writes must be
disabled.
automatically be enabled, based on the value of the
Table Pointer. The ID registers are mapped in
addresses 200000h through 200007h. These locations
read out normally, even after code protection.
Figure 3-6 demonstrates the code sequence required
to write the ID locations.
TABLE 3-6:
In order to modify the ID locations, refer to the
methodology described in Section 3.2.2, “Modifying
Code Memory”. As with code memory, the ID locations
must be erased before modified.
DS39583C-page 18
Step 1: Direct access to config memory.
Step 2: Configure device for single panel writes.
Step 3: Direct access to code memory.
Step 4: Load write buffer. Panel will be automatically determined by address.
Note:
Command
0000
0000
0000
0000
0000
0000
0000
0000
1100
0000
0000
0000
0000
0000
0000
0000
0000
1101
1101
1101
1111
0000
4-Bit
ID Location Programming
Even though multi-panel writes are dis-
abled, the user must still fill the 8-byte data
buffer for the panel.
The single panel that will be written will
8E A6
8C A6
0E 3C
6E F8
0E 00
6E F7
0E 06
6E F6
00 00
8E A6
9C A6
0E 20
6E F8
0E 00
6E F7
0E 00
6E F6
<LSB><MSB>
<LSB><MSB>
<LSB><MSB>
<LSB><MSB>
00 00
WRITE ID SEQUENCE
Data Payload
BSF
BSF
MOVLW 3Ch
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRH
MOVLW 06h
MOVWF TBLPTRL
Write 00h to 3C0006h to enable single panel writes.
BSF
BCF
MOVLW 20h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRH
MOVLW 00h
MOVWF TBLPTRL
Write 2 bytes and post-increment address by 2
Write 2 bytes and post-increment address by 2
Write 2 bytes and post-increment address by 2
Write 2 bytes and start programming
NOP - hold SCLK high for time P9
EECON1, EEPGD
EECON1, CFGS
EECON1, EEPGD
EECON1, CFGS
Core Instruction
 2010 Microchip Technology Inc.