PIC18F6622-I/PT Microchip Technology, PIC18F6622-I/PT Datasheet - Page 23

• Manufacturer Part Number: PIC18F6622-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6622-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.5
The code sequence detailed in Table 3-5 should be
used, except that the address used in “Step 2” will be in
the range of 000000h to 0007FFh, 000000h to
000FFFh or 000000h to 001FFFh, as defined by the
BBSIZ<1:0> bits in the CONFIG4L register (see
Table 5-1).
TABLE 3-9:
FIGURE 3-9:
© 2009 Microchip Technology Inc.
Step 1: Enable writes and direct access to configuration memory.
Step 2
Note 1:
Command
0000
0000
0000
0000
0000
0000
0000
0000
1111
0000
0000
0000
1111
0000
4-Bit
(1)
Boot Block Programming
: Set Table Pointer for configuration byte to be written. Write even/odd addresses.
Enabling the write protection of Configuration bits (WRTC = 0 in CONFIG6H) will prevent further writing of
Configuration bits. Always write all the Configuration bits before enabling the write protection for Configuration
bits.
8E A6
8C A6
0E 30
6E F8
0E 00
6E F7
0E 00
6E F6
<MSB ignored><LSB>
00 00
0E 01
6E F6
<MSB><LSB ignored>
00 00
SET ADDRESS POINTER TO CONFIGURATION LOCATION
Data Payload
CONFIGURATION PROGRAMMING FLOW
Delay P9 and P10
Time for Write
Configuration
Load Even
Program
Address
Done
Start
LSB
BSF
BSF
MOVLW 30h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRL
Load 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
MOVLW 01h
MOVWF TBLPTRL
Load 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
EECON1, EEPGD
EECON1, CFGS
3.6
Unlike code memory, the Configuration bits are
programmed a byte at a time. The Table Write, Begin
Programming 4-bit command (‘1111’) is used, but only
8 bits of the following 16-bit payload will be written. The
LSB of the payload will be written to even addresses and
the MSB will be written to odd addresses. The code
sequence to program two consecutive configuration
locations is shown in Table 3-9.
PIC18F872X FAMILY
Note:
Core Instruction
Configuration Bits Programming
Delay P9 and P10
The address must be explicitly written for
each byte programmed. The addresses
can not be incremented in this mode.
Time for Write
Configuration
Load Odd
Program
Address
Start
MSB
Done
DS39643C-page 23