PIC32MX360F512L-80I/PT Microchip Technology, PIC32MX360F512L-80I/PT Datasheet - Page 16
![IC PIC MCU FLASH 512K 100-TQFP](/photos/12/13/121330/c04-100-tqfp_sml.jpg)
PIC32MX360F512L-80I/PT
Manufacturer Part Number
PIC32MX360F512L-80I/PT
Description
IC PIC MCU FLASH 512K 100-TQFP
Manufacturer
Microchip Technology
Series
PIC® 32MXr
Datasheets
1.MA320002.pdf
(208 pages)
2.DM320001.pdf
(44 pages)
3.PIC32MX320F032H-40IPT.pdf
(48 pages)
4.PIC32MX320F032H-40IPT.pdf
(66 pages)
5.PIC32MX320F032H-40IPT.pdf
(22 pages)
6.PIC32MX320F032H-40IPT.pdf
(626 pages)
7.PIC32MX320F064H-40IMR.pdf
(172 pages)
Specifications of PIC32MX360F512L-80I/PT
Program Memory Type
FLASH
Program Memory Size
512KB (512K x 8)
Package / Case
100-TFQFP
Core Processor
MIPS32® M4K™
Core Size
32-Bit
Speed
80MHz
Connectivity
I²C, IrDA, LIN, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
85
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
2.3 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC32MX3xx
Core
MIPS
Data Bus Width
32 bit
Data Ram Size
32 KB
Interface Type
I2C , SPI , UART
Maximum Clock Frequency
80 MHz
Number Of Programmable I/os
85
Number Of Timers
5 x 16 bit
Operating Supply Voltage
2.3 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, DM320001, DM320002, MA320001
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit
Controller Family/series
PIC32
No. Of I/o's
85
Ram Memory Size
32KB
Cpu Speed
80MHz
No. Of Timers
6
Embedded Interface Type
EUART, I2C, PSP, SPI
No. Of Pwm Channels
5
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1000 - PIC32 BREAKOUT BOARDAC244003 - TEST BD MPLAB REAL ICE LOOPBACKAC244006 - KIT MPLAB REAL ICE TRACEDM320001 - KIT EVAL PIC32 STARTERAC164333 - MODULE SKT FOR PM3 100QFP
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC32MX360F512L-80I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC32MX360F512L-80I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC32MX
7.0
For 2-wire programming methods, the target device
must be placed in a special programming mode before
executing further steps.
The following steps are required to enter Programming
mode:
1.
2.
3.
Please refer to 20.0 “AC/DC Characteristics and
Timing Requirements” for timing requirements.
FIGURE 7-1:
DS61145G-page 16
Note:
The MCLR pin is briefly driven high, then low.
A 32-bit key sequence is clocked into PGDx.
MCLR is then driven high within a specified
period of time and held.
MCLR
V
PGDx
PGCx
DD
ENTERING PROGRAMMING
MODE
If a 4-wire programming method is used, it
is not necessary to enter the Programming
mode.
P6
ENTERING ENHANCED ICSP™ MODE
P14
P16
P20
V
b31
0
IH
b30
1
Program/Verify Entry Code = 0x4D434850
b29
0
P2B
b28
0
P2A
b27
1
The programming voltage applied to MCLR is V
which is essentially V
no minimum time requirement for holding at V
V
before presenting the key sequence on PGDx.
The key sequence is a specific 32-bit pattern: ‘0100
1101 0100 0011 0100 1000 0101 0000’ (the
acronym ‘MCHP’, in ASCII). The device will enter
Program/Verify mode only if the key sequence is valid.
The MSb of the Most Significant nibble must be shifted
in first.
Once the key sequence is complete, V
applied to MCLR and held at that level for as long as
Programming mode is to be maintained. An interval of
at least time P17 and P7 must elapse before presenting
data on PGDx. Signals appearing on PGDx before P7
has elapsed will not be interpreted as valid.
Upon successful entry, the program memory can be
accessed and programmed in serial fashion. While in
Programming mode, all unused I/Os are placed in the
high-impedance state.
IH
is removed, an interval of at least P16 must elapse
...
0
b3
0
b2
DD
0
b1
V
, in PIC32MX devices. There is
© 2010 Microchip Technology Inc.
IH
0
b0
P17
P7
IH
must be
IH
. After
IH
,