ATMEGA32-16PU Atmel, ATMEGA32-16PU Datasheet - Page 214

• Manufacturer Part Number: ATMEGA32-16PU
• Description: IC AVR MCU 32K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• A/d Inputs: 8-Channel, 10-Bit
• Cpu Speed: 16 MIPS
• Eeprom Memory: 1K Bytes
• Input Output: 32
• Interface: 2-Wire/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 32K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Data Rom Size: 1024 B
• Height: 4.83 mm
• Length: 52.58 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 13.97 mm
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 2KB
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADC Control and Status
Register A – ADCSRA
214
ATmega32(L)
Table 84. Input Channel and Gain Selections (Continued)
Note:
• Bit 7 – ADEN: ADC Enable
Writing this bit to one enables the ADC. By writing it to zero, the ADC is turned off. Turn-
ing the ADC off while a conversion is in progress, will terminate this conversion.
• Bit 6 – ADSC: ADC Start Conversion
In Single Conversion mode, write this bit to one to start each conversion. In Free Run-
ning Mode, write this bit to one to start the first conversion. The first conversion after
ADSC has been written after the ADC has been enabled, or if ADSC is written at the
same time as the ADC is enabled, will take 25 ADC clock cycles instead of the normal
13. This first conversion performs initialization of the ADC.
ADSC will read as one as long as a conversion is in progress. When the conversion is
complete, it returns to zero. Writing zero to this bit has no effect.
• Bit 5 – ADATE: ADC Auto Trigger Enable
When this bit is written to one, Auto Triggering of the ADC is enabled. The ADC will start
a conversion on a positive edge of the selected trigger signal. The trigger source is
selected by setting the ADC Trigger Select bits, ADTS in SFIOR.
• Bit 4 – ADIF: ADC Interrupt Flag
This bit is set when an ADC conversion completes and the Data Registers are updated.
The ADC Conversion Complete Interrupt is executed if the ADIE bit and the I-bit in
SREG are set. ADIF is cleared by hardware when executing the corresponding interrupt
handling vector. Alternatively, ADIF is cleared by writing a logical one to the flag.
Beware that if doing a Read-Modify-Write on ADCSRA, a pending interrupt can be dis-
abled. This also applies if the SBI and CBI instructions are used.
• Bit 3 – ADIE: ADC Interrupt Enable
When this bit is written to one and the I-bit in SREG is set, the ADC Conversion Com-
plete Interrupt is activated.
Bit
Read/Write
Initial Value
MUX4..0
11101
11110
11111
1. The differential input channels are not tested for devices in PDIP Package. This fea-
ture is only guaranteed to work for devices in TQFP and MLF Packages
Single Ended
Input
1.22 V (V
0 V (GND)
ADEN
R/W
7
0
BG
ADSC
R/W
)
6
0
ADATE
Positive Differential
Input
ADC5
N/A
R/W
5
0
ADIF
R/W
4
0
ADIE
R/W
3
0
ADPS2
Negative Differential
Input
ADC2
R/W
2
0
ADPS1
R/W
1
0
ADPS0
R/W
0
0
2503G–AVR–11/04
ADCSRA
Gain
1x