PIC16LF77-I/PT Microchip Technology, PIC16LF77-I/PT Datasheet - Page 101
![IC PIC MCU FLASH 8KX14 44TQFP](/photos/6/82/68251/c04-076_pt_sml.jpg)
PIC16LF77-I/PT
Manufacturer Part Number
PIC16LF77-I/PT
Description
IC PIC MCU FLASH 8KX14 44TQFP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Specifications of PIC16LF77-I/PT
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
33
Program Memory Size
14KB (8K x 14)
Program Memory Type
FLASH
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-TQFP, 44-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
PIC16LF77I/PT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16LF77-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
12.11 Interrupts
The PIC16F7X family has up to 12 sources of interrupt.
The interrupt control register (INTCON) records individ-
ual interrupt requests in flag bits. It also has individual
and global interrupt enable bits.
A global interrupt enable bit, GIE (INTCON<7>)
enables (if set) all unmasked interrupts, or disables (if
cleared) all interrupts. When bit GIE is enabled and an
interrupt’s flag bit and mask bit are set, the interrupt will
vector immediately. Individual interrupts can be dis-
abled through their corresponding enable bits in vari-
ous registers. Individual interrupt bits are set,
regardless of the status of the GIE bit. The GIE bit is
cleared on RESET.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine, as well as sets the GIE bit, which
re-enables interrupts.
FIGURE 12-10:
2002 Microchip Technology Inc.
Note:
PSPIF
PSPIE
CCP2IF
CCP2IE
Note 1:
(1)
(1)
Individual interrupt flag bits are set, regard-
less of the status of their corresponding
mask bit or the GIE bit.
ADIF
ADIE
TMR1IF
TMR1IE
PSP interrupt is implemented only on PIC16F74/77 devices.
RCIF
RCIE
TMR2IF
TMR2IE
INTERRUPT LOGIC
TXIF
TXIE
SSPIF
SSPIE
CCP1IF
CCP1IE
TMR0IF
TMR0IE
INTF
INTE
RBIF
RBIE
PEIE
GIE
The RB0/INT pin interrupt, the RB port change interrupt
and the TMR0 overflow interrupt flags are contained in
the INTCON register.
The peripheral interrupt flags are contained in the Spe-
cial Function Registers, PIR1 and PIR2. The corre-
sponding interrupt enable bits are contained in Special
Function Registers, PIE1 and PIE2, and the peripheral
interrupt enable bit is contained in Special Function
Register, INTCON.
When an interrupt is responded to, the GIE bit is
cleared to disable any further interrupt, the return
address is pushed onto the stack and the PC is loaded
with 0004h. Once in the Interrupt Service Routine, the
source(s) of the interrupt can be determined by polling
the interrupt flag bits. The interrupt flag bit(s) must be
cleared in software before re-enabling interrupts to
avoid recursive interrupts.
For external interrupt events, such as the INT pin or
PORTB change interrupt, the interrupt latency will be
three or four instruction cycles. The exact latency
depends when the interrupt event occurs, relative to
the current Q cycle. The latency is the same for one or
two-cycle instructions. Individual interrupt flag bits are
set, regardless of the status of their corresponding
mask bit, PEIE bit, or the GIE bit.
Wake-up (If in SLEEP mode)
PIC16F7X
Interrupt to CPU
DS30325B-page 99