PIC16F874-04I/P Microchip Technology, PIC16F874-04I/P Datasheet - Page 55
![IC MCU FLASH 4KX14 EE 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC16F874-04I/P
Manufacturer Part Number
PIC16F874-04I/P
Description
IC MCU FLASH 4KX14 EE 40DIP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F688T-ISL.pdf
(688 pages)
3.PIC16F873-04SO.pdf
(218 pages)
4.PIC16F873-04SO.pdf
(5 pages)
5.PIC16F873-04SO.pdf
(5 pages)
Specifications of PIC16F874-04I/P
Core Size
8-Bit
Program Memory Size
7KB (4K x 14)
Oscillator Type
External
Core Processor
PIC
Speed
4MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
33
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
192 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 8x10b
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Controller Family/series
PIC16F
No. Of I/o's
33
Eeprom Memory Size
128Byte
Ram Memory Size
192Byte
Cpu Speed
4MHz
No. Of
RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
444-1001 - DEMO BOARD FOR PICMICRO MCU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F874-04I/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC16F874-04I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
6.4
If control bit T1SYNC (T1CON<2>) is set, the external
clock input is not synchronized. The timer continues to
increment asynchronous to the internal phase clocks.
The timer will continue to run during SLEEP and can
generate an interrupt-on-overflow, which will wake-up
the processor. However, special precautions in soft-
ware are needed to read/write the timer (Section 6.4.1).
In Asynchronous Counter mode, Timer1 cannot be
used as a time-base for capture or compare opera-
tions.
6.4.1
Reading TMR1H or TMR1L while the timer is running
from an external asynchronous clock, will guarantee a
valid read (taken care of in hardware). However, the
user should keep in mind that reading the 16-bit timer
in two 8-bit values itself, poses certain problems, since
the timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write conten-
tion may occur by writing to the timer registers, while
the register is incrementing. This may produce an
unpredictable value in the timer register.
Reading the 16-bit value requires some care. Exam-
ples 12-2 and 12-3 in the PICmicro™ Mid-Range MCU
Family Reference Manual (DS33023) show how to
read and write Timer1 when it is running in Asynchro-
nous mode.
6.5
A crystal oscillator circuit is built-in between pins T1OSI
(input) and T1OSO (amplifier output). It is enabled by
setting control bit T1OSCEN (T1CON<3>). The oscilla-
tor is a low power oscillator, rated up to 200 kHz. It will
continue to run during SLEEP. It is primarily intended
for use with a 32 kHz crystal. Table 6-1 shows the
capacitor selection for the Timer1 oscillator.
The Timer1 oscillator is identical to the LP oscillator.
The user must provide a software time delay to ensure
proper oscillator start-up.
2001 Microchip Technology Inc.
Timer1 Operation in
Asynchronous Counter Mode
Timer1 Oscillator
READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER
MODE
TABLE 6-1:
6.6
If the CCP1 or CCP2 module is configured in Compare
mode
(CCP1M3:CCP1M0 = 1011), this signal will reset
Timer1.
Timer1 must be configured for either Timer or Synchro-
nized Counter mode to take advantage of this feature.
If Timer1 is running in Asynchronous Counter mode,
this RESET operation may not work.
In the event that a write to Timer1 coincides with a spe-
cial event trigger from CCP1 or CCP2, the write will
take precedence.
In this mode of operation, the CCPRxH:CCPRxL regis-
ter pair effectively becomes the period register for
Timer1.
Note 1: Higher capacitance increases the stability
32.768 kHz
Osc Type
Note:
100 kHz
200 kHz
These values are for design guidance only.
LP
2: Since each resonator/crystal has its own
to
Resetting Timer1 using a CCP
Trigger Output
of oscillator, but also increases the start-up
time.
characteristics, the user should consult the
resonator/crystal manufacturer for appro-
priate values of external components.
The special event triggers from the CCP1
and CCP2 modules will not set interrupt
flag bit TMR1IF (PIR1<0>).
generate
Epson C-001R32.768K-A
Epson C-2 100.00 KC-P
100 kHz
200 kHz
32 kHz
STD XTL 200.000 kHz
Freq.
CAPACITOR SELECTION FOR
THE TIMER1 OSCILLATOR
Crystals Tested:
a
PIC16F87X
“special
33 pF
15 pF
15 pF
C1
DS30292C-page 53
event
± 20 PPM
± 20 PPM
± 20 PPM
33 pF
15 pF
15 pF
C2
trigger”