PIC16F876-20/SP Microchip Technology, PIC16F876-20/SP Datasheet - Page 54
![IC MCU FLASH 8KX14 EE 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC16F876-20/SP
Manufacturer Part Number
PIC16F876-20/SP
Description
IC MCU FLASH 8KX14 EE 28DIP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F688T-ISL.pdf
(688 pages)
3.PIC16C770-ISO.pdf
(8 pages)
4.PIC16F873-04SO.pdf
(218 pages)
5.PIC16F873-04SO.pdf
(5 pages)
6.PIC16F873-04SO.pdf
(5 pages)
Specifications of PIC16F876-20/SP
Program Memory Type
FLASH
Program Memory Size
14KB (8K x 14)
Package / Case
28-DIP (0.300", 7.62mm)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Eeprom Size
256 x 8
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC16F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
368 B
Interface Type
MSSP/PSP/USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
22
Number Of Timers
3
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 70 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
Minimum Operating Temperature
0 C
On-chip Adc
5-ch x 10-bit
Data Rom Size
256 B
A/d Bit Size
10 bit
A/d Channels Available
5
Height
3.3 mm
Length
34.67 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4 V
Width
7.24 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F876-20/SP
Manufacturer:
MICROCHIP
Quantity:
6 264
Part Number:
PIC16F876-20/SP
Manufacturer:
MIC
Quantity:
20 000
PIC16F87X
6.1
Timer mode is selected by clearing the TMR1CS
(T1CON<1>) bit. In this mode, the input clock to the
timer is F
(T1CON<2>) has no effect, since the internal clock is
always in sync.
FIGURE 6-1:
6.3
Counter mode is selected by setting bit TMR1CS. In
this mode, the timer increments on every rising edge of
clock input on pin RC1/T1OSI/CCP2, when bit
T1OSCEN is set, or on pin RC0/T1OSO/T1CKI, when
bit T1OSCEN is cleared.
FIGURE 6-2:
DS30292C-page 52
T1CKI
(Default High)
T1CKI
(Default Low)
Note: Arrows indicate counter increments.
Note 1: When the T1OSCEN bit is cleared, the inverter is turned off. This eliminates power drain.
RC0/T1OSO/T1CKI
RC1/T1OSI/CCP2
Timer1 Operation in Timer Mode
Timer1 Operation in Synchronized
Counter Mode
OSC
/4. The synchronize control bit T1SYNC
Set Flag bit
TMR1IF on
Overflow
TIMER1 INCREMENTING EDGE
TIMER1 BLOCK DIAGRAM
(2)
TMR1H
T1OSC
TMR1
TMR1L
Oscillator
Enable
T1OSCEN
(1)
Clock
Internal
F
OSC
/4
TMR1ON
6.2
Timer1 may operate in either a Synchronous, or an
Asynchronous mode, depending on the setting of the
TMR1CS bit.
When Timer1 is being incremented via an external
source, increments occur on a rising edge. After Timer1
is enabled in Counter mode, the module must first have
a falling edge before the counter begins to increment.
If T1SYNC is cleared, then the external clock input is
synchronized with internal phase clocks. The synchro-
nization is done after the prescaler stage. The
prescaler stage is an asynchronous ripple-counter.
In this configuration, during SLEEP mode, Timer1 will
not increment even if the external clock is present,
since the synchronization circuit is shut-off. The
prescaler, however, will continue to increment.
On/Off
TMR1CS
1
0
Timer1 Counter Operation
T1CKPS1:T1CKPS0
T1SYNC
Prescaler
1, 2, 4, 8
0
1
2
2001 Microchip Technology Inc.
Synchronized
Clock Input
Synchronize
Q Clock
det