DSPIC33FJ128GP306-I/PT Microchip Technology, DSPIC33FJ128GP306-I/PT Datasheet - Page 65

• Manufacturer Part Number: DSPIC33FJ128GP306-I/PT
• Description: IC DSPIC MCU/DSP 128K 64TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128GP306-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 64-TFQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC33F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Data Ram Size: 16 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Minimum Operating Temperature: - 40 C
• Package: 64TQFP
• Device Core: dsPIC
• Family Name: dSPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Interface Type: I2C/SPI/UART
• On-chip Adc: 18-chx10-bit|18-chx12-bit
• Number Of Timers: 9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1001 - DSPIC33 BREAKOUT BOARDDM300024 - KIT DEMO DSPICDEM 1.1DV164033 - KIT START EXPLORER 16 MPLAB ICD2MA330012 - MODULE DSPIC33 100P TO 84QFPMA330011 - MODULE DSPIC33 100P TO 100QFPDM300019 - BOARD DEMO DSPICDEM 80L STARTERDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

can operate on any W register pointer. However, it is not
advisable to use W14 or W15 for Modulo Addressing
since these two registers are used as the Stack Frame
Pointer and Stack Pointer, respectively.
In general, any particular circular buffer can only be
configured to operate in one direction as there are
certain restrictions on the buffer start address (for incre-
menting buffers), or end address (for decrementing
buffers), based upon the direction of the buffer.
The only exception to the usage restrictions is for
buffers which have a power-of-2 length. As these
buffers satisfy the start and end address criteria, they
may operate in a bidirectional mode (i.e., address
boundary checks will be performed on both the lower
and upper address boundaries).
4.4.1
The Modulo Addressing scheme requires that a starting
and ending address be specified and loaded into the
16-bit Modulo Buffer Address registers: XMODSRT,
XMODEND,
Table 4-1).
FIGURE 4-7:
© 2009 Microchip Technology Inc.
Note:
Address
0x1100
0x1163
Byte
START AND END ADDRESS
Y
calculations assume word sized data (LSb
of every EA is always clear).
Start Addr = 0x1100
End Addr = 0x1163
Length = 0x0032 words
YMODSRT
space
MODULO ADDRESSING OPERATION EXAMPLE
Modulo
and
YMODEND
Addressing
dsPIC33FJXXXGPX06/X08/X10
MOV
MOV
MOV
MOV
MOV
MOV
MOV
MOV
DO
MOV
AGAIN: INC
(see
EA
#0x1100, W0
W0, XMODSRT
#0x1163, W0
W0, MODEND
#0x8001, W0
W0, MODCON
#0x0000, W0
#0x1110, W1
AGAIN, #0x31
W0, [W1++]
W0, W0
The length of a circular buffer is not directly specified. It
is
corresponding start and end addresses. The maximum
possible length of the circular buffer is 32K words
(64 Kbytes).
4.4.2
The Modulo and Bit-Reversed Addressing Control
register, MODCON<15:0>, contains enable flags as well
as a W register field to specify the W Address registers.
The XWM and YWM fields select which registers will
operate with Modulo Addressing. If XWM = 15, X RAGU
and X WAGU Modulo Addressing is disabled. Similarly, if
YWM = 15, Y AGU Modulo Addressing is disabled.
The X Address Space Pointer W register (XWM), to
which Modulo Addressing is to be applied, is stored in
MODCON<3:0> (see Table 4-1). Modulo Addressing is
enabled for X data space when XWM is set to any value
other than ‘15’ and the XMODEN bit is set at
MODCON<15>.
The Y Address Space Pointer W register (YWM) to
which Modulo Addressing is to be applied is stored in
MODCON<7:4>. Modulo Addressing is enabled for Y
data space when YWM is set to any value other than
‘15’ and the YMODEN bit is set at MODCON<14>.
determined
;set modulo start address
;set modulo end address
;enable W1, X AGU for modulo
;W0 holds buffer fill value
;point W1 to buffer
;fill the 50 buffer locations
;fill the next location
;increment the fill value
W ADDRESS REGISTER
SELECTION
by
the
difference
DS70286C-page 63
between
the