PIC16F76-I/SS Microchip Technology, PIC16F76-I/SS Datasheet - Page 288

• Manufacturer Part Number: PIC16F76-I/SS
• Description: IC MCU FLASH 8KX14 A/D 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F76-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 28-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 8-bit
• Controller Family/series: PIC16F
• No. Of I/o's: 22
• Ram Memory Size: 368Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164307 - MODULE SKT FOR PM3 28SSOPXLT28SS-1 - SOCKET TRANSITION ICE 28SSOP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
17.3.4
DS31017A-page 17-12
Master Mode
The master can initiate the data transfer at any time because it controls the SCK. The master
determines when the slave (Processor 2,
tocol.
In master mode the data is transmitted/received as soon as the SSPBUF register is written to. If
the SPI is only going to receive, the SDO output could be disabled (programmed as an input).
The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed
clock rate. As each byte is received, it will be loaded into the SSPBUF register as if a normal
received byte (interrupts and status bits appropriately set). This could be useful in receiver appli-
cations as a “line activity monitor” mode.
The clock polarity is selected by appropriately programming the CKP bit (SSPCON1<4>). This
then would give waveforms for SPI communication as shown in
Figure 17-9
user programmable to be one of the following:
• F
• F
• F
• Timer2 output/2
This allows a maximum data rate (at 20 MHz) of 8.25 Mbps.
Figure 17-6
valid before there is a clock edge on SCK. The change of the input sample is shown based on
the state of the SMP bit. The time when the SSPBUF is loaded with the received data is shown.
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
where the MSb is transmitted first. In master mode, the SPI clock rate (bit rate) is
Shows the waveforms for master mode. When the CKE bit is set, the SDO data is
CY
)
CY
CY
)
)
Preliminary
Figure
17-5) is to broadcast data by the software pro-
Figure
1997 Microchip Technology Inc.
17-6,
Figure
17-8, and