PIC18LF2420-I/ML Microchip Technology, PIC18LF2420-I/ML Datasheet - Page 98

• Manufacturer Part Number: PIC18LF2420-I/ML
• Description: IC PIC MCU FLASH 8KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2420-I/ML

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 10-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F2420/2520/4420/4520
9.2
The PIR registers contain the individual flag bits for the
peripheral interrupts. Due to the number of peripheral
interrupt sources, there are two Peripheral Interrupt
Request Flag registers (PIR1 and PIR2).
REGISTER 9-4:
DS39631E-page 96
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
PSPIF
R/W-0
PIR Registers
(1)
This bit is unimplemented on 28-pin devices and will read as ‘0’.
PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
RCIF: EUSART Receive Interrupt Flag bit
1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read)
0 = The EUSART receive buffer is empty
TXIF: EUSART Transmit Interrupt Flag bit
1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written)
0 = The EUSART transmit buffer is full
SSPIF: Master Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode.
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
R/W-0
ADIF
PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1
W = Writable bit
‘1’ = Bit is set
RCIF
R-0
TXIF
R-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
SSPIF
Note 1: Interrupt flag bits are set when an interrupt
(1)
2: User software should ensure the appropri-
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Interrupt Enable bit, GIE (INTCON<7>).
ate interrupt flag bits are cleared prior to
enabling an interrupt and after servicing
that interrupt.
CCP1IF
R/W-0
© 2008 Microchip Technology Inc.
x = Bit is unknown
TMR2IF
R/W-0
TMR1IF
R/W-0
bit 0