PIC16LC621-04/SO Microchip Technology, PIC16LC621-04/SO Datasheet - Page 60
![IC MCU OTP 1KX14 COMP 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
PIC16LC621-04/SO
Manufacturer Part Number
PIC16LC621-04/SO
Description
IC MCU OTP 1KX14 COMP 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheet
1.PIC16C620A-04SO.pdf
(128 pages)
Specifications of PIC16LC621-04/SO
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
13
Program Memory Size
1.75KB (1K x 14)
Program Memory Type
OTP
Ram Size
80 x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 6 V
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
18-SOIC (7.5mm Width)
Core
PIC
Processor Series
PIC16LC
Data Bus Width
8 bit
Maximum Clock Frequency
4 MHz
Data Ram Size
96 B
Data Rom Size
80 B
Number Of Programmable I/os
13
Number Of Timers
8
Operating Supply Voltage
2.5 V to 6 V
Mounting Style
SMD/SMT
Height
2.05 mm
Length
11.55 mm
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Width
7.5 mm
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
Connectivity
-
Lead Free Status / Rohs Status
Details
PIC16C62X
9.7
The Watchdog Timer is a free running on-chip RC oscil-
lator which does not require any external components.
This RC oscillator is separate from the RC oscillator of
the CLKIN pin. That means that the WDT will run, even
if the clock on the OSC1 and OSC2 pins of the device
has been stopped, for example, by execution of a
SLEEP
time-out generates a device RESET. If the device is in
SLEEP mode, a WDT time-out causes the device to
wake-up and continue with normal operation. The WDT
can be permanently disabled by programming the
configuration bit WDTE as clear (Section 9.1).
9.7.1
The WDT has a nominal time-out period of 18 ms, (with
no prescaler). The time-out periods vary with tempera-
ture, V
FIGURE 9-17:
TABLE 9-7:
DS30235J-page 58
Address Name
2007h
81h
Legend: Shaded cells are not used by the Watchdog Timer.
Note:
Note:
DD
instruction. During normal operation, a WDT
Watchdog Timer (WDT)
and process variations from part to part (see
Config. bits —
OPTION
WDT PERIOD
_
+ = Reserved for future use
= Unimplemented location, read as “0”
T0SE, T0CS, PSA, PS<2:0> are bits in the OPTION register.
SUMMARY OF WATCHDOG TIMER REGISTERS
RBPU
WATCHDOG TIMER BLOCK DIAGRAM
Bit 7
Enable Bit
Watchdog
BODEN
INTEDG
Timer
WDT
Bit 6
From TMR0 Clock Source
CP1
T0CS
Bit 5
(Figure 6-6)
CP0
T0SE
1
Bit 4
0
PSA
M
U
X
PWRTE
PSA
Bit 3
DC specs). If longer time-out periods are desired, a
prescaler with a division ratio of up to 1:128 can be
assigned to the WDT under software control by writing
to the OPTION register. Thus, time-out periods up to
2.3 seconds can be realized.
The
and the postscaler, if assigned to the WDT, and prevent
it from timing out and generating a device RESET.
The TO bit in the STATUS register will be cleared upon
a Watchdog Timer time-out.
9.7.2
It should also be taken in account that under worst case
conditions (V
WDT prescaler) it may take several seconds before a
WDT time-out occurs.
WDTE
PS2
Bit 2
CLRWDT
0
Time-out
MUX
8 - to -1 MUX
WDT
Postscaler
FOSC1
WDT PROGRAMMING
CONSIDERATIONS
PS1
DD
Bit 1
and
1
= Min., Temperature = Max., max.
8
SLEEP
FOSC0
PS0
Bit 0
2003 Microchip Technology Inc.
To TMR0 (Figure 6-6)
PSA
instructions clear the WDT
—
1111 1111
POR Reset
PS<2:0>
Value on
—
1111 1111
Value on all
RESETS
other