PIC18F27J13-I/SP Microchip Technology, PIC18F27J13-I/SP Datasheet

no-image

PIC18F27J13-I/SP

Manufacturer Part Number
PIC18F27J13-I/SP
Description
IC PIC MCU 128KB FLASH 28SPDIP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/SP

Core Size
8-Bit
Program Memory Size
128KB (64K x 16)
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Type
FLASH
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
2.15 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Controller Family/series
PIC18
Cpu Speed
48MHz
Digital Ic Case Style
DIP
Supply Voltage Range
1.8V To 5.5V
Embedded Interface Type
I2C, SPI, USART
Rohs Compliant
Yes
Core
PIC
Processor Series
PIC18F
Data Bus Width
8 bit
Maximum Clock Frequency
48 MHz
Data Ram Size
3.76 KB
On-chip Adc
Yes
Number Of Programmable I/os
2
Number Of Timers
8
Operating Supply Voltage
2.15 V to 3.6 V
Operating Temperature Range
- 40 C to + 85 C
A/d Bit Size
12 bit
A/d Channels Available
10
Height
3.43 mm
Interface Type
I2C, SPI, USART
Length
34.4 mm
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.15 V
Width
7.24 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
Eeprom Size
-
Lead Free Status / Rohs Status
 Details
The PIC18F47J13 Family devices that you have
received conform functionally to the current Device
Data Sheet (DS39974A), except for the anomalies
described in this document.
The silicon issues discussed in the following pages are
for silicon revisions with the Device and Revision IDs
listed in
Table
The errata described in this document will be
addressed in future revisions of the PIC18F47J13
Family silicon.
Data Sheet clarifications and corrections start on page 5,
following the discussion of silicon issues.
The silicon revision level can be identified using the
current version of MPLAB
grammers, debuggers, and emulation tools, which are
available at the Microchip corporate web site
(www.microchip.com).
TABLE 1:
 2011 Microchip Technology Inc.
PIC18F47J13
PIC18F46J13
PIC18F27J13
PIC18F26J13
PIC18LF47J13
PIC18LF46J13
PIC18LF27J13
PIC18LF26J13
Note 1:
Note:
2.
2:
Table
Part Number
The Device IDs (DEVID and DEVREV) are located at the last two implemented addresses of configuration
memory space. They are shown in hexadecimal in the format “DEVID DEVREV”.
Refer to the “PIC18F2XJXX/4XJXX Family Flash Microcontroller Programming Specification” (DS39687)
for detailed information on Device and Revision IDs for your specific device.
This document summarizes all silicon
errata issues from all revisions of silicon,
previous as well as current. Only the
issues indicated in the last column of
Table 2
revision (A1).
1. The silicon issues are summarized in
SILICON DEVREV VALUES
Silicon Errata and Data Sheet Clarification
apply to the current silicon
®
IDE and Microchip’s pro-
Device ID
PIC18F47J13 Family
2CDh
2CFh
2CBh
2DFh
2DDh
2DBh
2C9h
2D9h
PIC18F47J13 FAMILY
(1)
For example, to identify the silicon revision level using
MPLAB IDE in conjunction with MPLAB ICD 2 or
PICkit™ 3:
1.
2.
3.
4.
The DEVREV values for the various PIC18F47J13
Family silicon revisions are shown in
01h
A1
Note:
Using the appropriate interface, connect the
device to the MPLAB ICD 2 programmer/
debugger or PICkit 3.
From the main menu in MPLAB IDE, select
Configure>Select Device, and then select the
target part number in the dialog box.
Select
(Debugger>Select Tool).
Perform a “Connect” operation to the device
(Debugger>Connect). Depending on the devel-
opment tool used, the part number and Device
Revision ID value appear in the Output window.
Revision ID for Silicon Revision
If you are unable to extract the silicon
revision level, please contact your local
Microchip sales office for assistance.
the
MPLAB
hardware
Table
DS80503D-page 1
(2)
1.
tool

Related parts for PIC18F27J13-I/SP

PIC18F27J13-I/SP Summary of contents

Page 1

... Microchip corporate web site (www.microchip.com). TABLE 1: SILICON DEVREV VALUES Part Number PIC18F47J13 PIC18F46J13 PIC18F27J13 PIC18F26J13 PIC18LF47J13 PIC18LF46J13 PIC18LF27J13 PIC18LF26J13 The Device IDs (DEVID and DEVREV) are located at the last two implemented addresses of configuration Note 1: memory space. They are shown in hexadecimal in the format “ ...

Page 2

... SCL clock stream and RCEN bit slave reception, the module may have problems receiving correct data. If interrupts are enabled, disabling and re-enabling the module requires delay. (1) Affected Revisions  2011 Microchip Technology Inc. ...

Page 3

... Before attempting to set the PLLEN bit, config- ure OSCCON<6:4> to 0b110 or 0b111 to select the 4 MHz or 8 MHz INTOSC postscaler. Affected Silicon Revisions A1 X  2011 Microchip Technology Inc. PIC18F47J13 FAMILY 3. Module: Analog-to-Digital Converter (ADC) At the beginning of sample acquisition, one or more small pull-up pulses (approximately 25 ns long) may output to the currently selected ANx analog channel ...

Page 4

... EUSART module (sets SPEN, CREN or TXEN = 1). See Example Affected Silicon Revisions A1 X ;or RCSTA2 if EUSART2 ;1 Tcy delay ;1 Tcy delay (two total slave reception, enable the Synchronous Asynchronous Receiver Transmitter (EUSART) delay after any instruction that re  2011 Microchip Technology Inc. ...

Page 5

... ECJ-3YX1C106K Panasonic ECJ-4YB1C106K Murata GRM32DR71C106KA01L Murata GRM31CR61C106KC31L  2011 Microchip Technology Inc. PIC18F47J13 FAMILY On “LF” devices, the V a voltage supply at the V Section 30.0 information on V Note that the “LF” versions of these devices are provided with the voltage regulator permanently disabled ...

Page 6

... For example, choose a ceramic capacitor rated at 16V for the 2.5V core voltage. Suggested capacitors are shown in Table 2-1.  2011 Microchip Technology Inc ...

Page 7

... Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. 2:  2011 Microchip Technology Inc. PIC18F47J13 FAMILY 3. Module: Electrical Characteristics Changes, shown in bold, have been made to the D060, D061 and D063 rows in ...

Page 8

... SMP = 0 (sampled at middle of bit) ;CKP = 0, SPI Master mode, Fosc/4 ;MSSP2 initialized ;Enable the MSSP2 module ;Full duplex, RX/TXINC enabled, no SSCON ;DLYINTEN is set, so DLYCYC3:DLYCYC0 = 1111 ;Minimum delay between bytes, interrupt ;only once when the transaction is complete  2011 Microchip Technology Inc. ...

Page 9

... DMABCL BeginXfer: bsf DMACON1, DMAEN ;Execute whatever  2011 Microchip Technology Inc. PIC18F47J13 FAMILY ;Somewhere else in our project, lets assume we have ;allocated some RAM for use as SPI receive and ;transmit buffers. ;Reserve 0x500-0x6FF for use as our SPI ;receive data buffer in this example ...

Page 10

... Rev B Document 10/2010) Added data sheet clarification issues 1 (Guidelines For Getting Started with PIC18FJ Microcontrollers) and 2 (Reset). Rev C Document 11/2010 Added data sheet clarification issue 3 (Electrical Characteristics). Rev D Document 1/2011 Added data sheet clarification issue 4 (Code Example). DS80503D-page 10  2011 Microchip Technology Inc. ...

Page 11

... PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...

Page 12

... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350  2011 Microchip Technology Inc. 08/04/10 ...

Related keywords