PIC16F627-04/SO Microchip Technology, PIC16F627-04/SO Datasheet - Page 108

• Manufacturer Part Number: PIC16F627-04/SO
• Description: IC MCU FLASH 1KX14 COMP 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F627-04/SO

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-SOIC (7.5mm Width)
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 224Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 224 B
• Interface Type: SCI, USART
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Data Converters: -
• Lead Free Status / Rohs Status: Details

PIC16F62X
14.12 In-Circuit Serial Programming
The PIC16F62X microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware, or a custom
firmware to be programmed.
The device is placed into a Program/Verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After RESET, to place the device into Programming/
Verify mode, the program counter (PC) is at location
00h. A 6-bit command is then supplied to the device.
Depending on the command, 14 bits of program data
are then supplied to or from the device, depending if
the command was a load or a read. For complete
details of serial programming, please refer to the
Programming Specifications.
A typical in-circuit serial programming connection is
shown in Figure 14-18.
FIGURE 14-18:
DS40300C-page 106
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
PP
) pin from V
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
IL
to V
IHH
(see programming
V
V
RA5/MCLR/V
RB6/PGC
RB7/PGD
V
PIC16F62X
DD
DD
SS
PP
Preliminary
14.13 Low Voltage Programming
The LVP bit of the configuration word, enables the low
voltage programming. This mode allows the microcon-
troller to be programmed via ICSP using only a 5V
source. This mode removes the requirement of V
be placed on the MCLR pin. The LVP bit is normally
erased to '1', which enables the low voltage program-
ming. In this mode, the RB4/PGM pin is dedicated to
the programming function and ceases to be a general
purpose I/O pin. The device will enter Programming
mode when a '1' is placed on the RB4/PGM pin. The
HV Programming mode is still available by placing V
on the MCLR pin.
If Low voltage Programming mode is not used, the LVP
bit can be programmed to a '0', and RB4/PGM
becomes a digital I/O pin. To program the device, V
must be placed onto MCLR during programming. The
LVP bit may only be programmed when programming
is entered with V
programmed when programming is entered with RB4/
PGM.
It should be noted, that once the LVP bit is programmed
to 0, High voltage Programming mode can be used to
program the device.
Note 1: While in this mode, the RB4 pin can no
2: V
longer be used as a general purpose I/O
pin.
program operations while in low voltage
Programming mode.
DD
IHH
must be 5.0V +10% during erase/
on MCLR. The LVP bit cannot be
 2003 Microchip Technology Inc.
IHH
IHH
IHH
to