PIC12F635-I/MD Microchip Technology, PIC12F635-I/MD Datasheet - Page 118

• Manufacturer Part Number: PIC12F635-I/MD
• Description: IC PIC MCU FLASH 1KX14 8DFN
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F635-I/MD

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 5
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DFN
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 64Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164326 - MODULA SKT PM3 20QFNXLT08DFN2 - SOCKET TRANSITION ICE 14DIP/8DFNAC162057 - MPLAB ICD 2 HEADER 14DIPXLT08DFN - SOCKET TRANSITION ICE 8DFN
• Data Converters: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC12F635/PIC16F636/639
11.31.3
An analog current is available at the LFDATA pin when
the Received Signal Strength Indicator (RSSI) output is
selected for the AFE’s Configuration register. The analog
current is linearly proportional to the input signal strength
(see Figure 11-15).
All timers in the circuit, such as inactivity timer, alarm
timer, and AGC settling time, are disabled during the
RSSI mode. Therefore, the RSSI output is not affected
by the AGC settling time, and available immediately
when the RSSI option is selected. The AFE enters
Active mode immediately when the RSSI output is
selected. The MCU I/O pin (RC3) connected to the
LFDATA pin, must be set to high-impedance state
during the RSSI Output mode.
When the AFE receives an SPI command during the
RSSI output, the RSSI mode is temporary disabled
until the SPI interface communication is completed. It
returns to the RSSI mode again after the SPI interface
communication is completed. The AFE holds the RSSI
mode until another output type is selected (CS low
turns off the RSSI signal). To obtain the RSSI output
for a particular input channel, or to save operating
power, the input channel can be individually enabled
or disabled. If more than one channel is enabled, the
RSSI output is from the strongest signal channel.
There will be no valid output if all three channels are
disabled.
Related AFE Configuration register bits:
• Configuration Register 1 (Register 11-2),
• Configuration Register 2 (Register 11-3),
• Configuration Register 0 (Register 11-1): all bits
DS41232D-page 116
DATOUT<8:7>:
RSSIFET<8>:
Note:
are affected.
bit 8
0
0
1
1
bit 7
RECEIVED SIGNAL STRENGTH
INDICATOR (RSSI) OUTPUT
The pull-down MOSFET option is valid
only when the RSSI output is selected.
The MOSFET is not controllable by users
when Demodulated or Carrier Clock
output option is selected.
0: Demodulated Output
1: Carrier Clock Output
0: RSSI Output
1: RSSI Output
0: Pull-Down MOSFET off
1: Pull-Down MOSFET on.
FIGURE 11-14:
(controlled by Config. 2, bit 8)
RSSI Pull-down MOSFET
RSSI Output Current
RSSIFET
Generator
V
DD
Off
if RSSI active
RSSI OUTPUT PATH
© 2007 Microchip Technology Inc.
RC3/LFDATA/RSSI/CCLK Pin
Current Output